====== OLED Display Information ======

/* FIXME

TODO: Fotos SX-Zentralmodul, Fotos RX, Überprüfen ob Anleitung MX noch i.O.

FIXME */


===== General Notes ======

OLED displays have an unavoidable process of wear and tear. To ensure that the OLED displays last as long as possible, use the instructions in this document.

==== Do not use maximum brightness ====
Maximum brightness of console surfaces is not recommended to use, especially for a longer time. You should use maximum brightness only when necessary due to environmental conditions (e.g., outside broadcasting). Always keep in mind, that OLED displays running on maximum brightness will wear and tear very fast and will not last very long.

**Use ''Standard'' or ''Dimmed'' illumination levels as default instead**. On control surfaces that do not support illumination levels, use ''Auto Dim'' to set standby.

<WRAP center round important 80%>
**Important**\\  In older firmware versions, default illumination level is always ''maximum brightness''. OLED displays will not last very long under these conditions. Make sure to use a firmware version which supports illumination levels. See [[#Brightness_Settings|Brightness Settings]] below.
</WRAP>

==== Enable auto dim or standby ====

For times when the consoles are not in use for a longer time, enable ''Auto dim'' functionality. This will dim or switch off the surface after a certain time of inactivity. You can define the timing, when the control surface will dim or switch off. Use this function for studios that are not in use the full day, for example to switch off the control surface at night.


==== Use brightness keys ====

''Brightness'' keys allow the user to change surface brightness to a defined value. Brightness can be separately applied to TFTs and to console surfaces (including OLEDs and push buttons). With this solution console brightness can additionally be adjusted on demand. Also use brightness keys in combination with auto dim functionality.

===== Brightness settings =====

Toolbox software supports adjusting default brightness levels. Also ''auto dim'' / stand by mode for surfaces is possible.

=== Firmware version 8.x & Toolbox8 ===

Console illumination features are supported with all Versions of TB8 and firmware version 8.x. See [[tb8:console_illumination|Console Illumination]] for information on setting auto dim and default brightness levels. See [[tb8:console#misc_functions|Console / Key Functions]] for information on how to set up brightness keys.

=== Firmware version 7.4 & Toolbox5 ===

Since **Firmware Version 7.4.34** console illumination and auto dim is possible for Series 52 devices using firmware version 7. Consider an update to this version. See [[installation:update|Firmware update recommendations]]

See [[tb5:console_illumination|Console Illumination]] for information on setting auto dim and default brightness levels. See [[tb5:console#misc_functions|Console / Key Functions]] for information on how to set up brightness keys.

===== OLED display exchange =====

Exchanging OLED displays on all DHD Modules is possible.

<WRAP center round info 80%>
**Note**\\  For getting spare parts and before exchanging the OLEDs always contact your local DHD distributor first! 
</WRAP>

==== 52/SX fader modules ====

=== Exchange on 52-1020A, 52-1021A, 52-1024A, 52-1025A ===

  - Remove encoder knobs and housing. \\ Screw: 14 pcs countersunk M2x4,\\ Tool: Torx T6\\ {{ :oled:52-1020_oled-wechsel_schritt_1s.jpg?600 |}}
  - Remove  main PCB from front panel. \\ Screw: 11 pcs (52-1020A, 52-1021A) or 9 pcs (52-1024A, 52-1025A) hexagon button head screw M3x6,\\ Tool: Screwdriver Hexagon 2mm \\ {{ :oled:52-1020_oled-wechsel_schritt_2s.jpg?600 |}}
  - Disconnect the cable connector at each fader \\ {{ :oled:cable_connector_-_fader_52sx.jpg?600 |}}
  - Remove srews in OLED boards \\ Screw: 10 pcs button head screw M2x5,\\ Tool: Torx T6 \\ <WRAP center round alert 60%>**WARNING**\\ Do not touch the green flex-PCB areas at the OLED diplays. Only use the solid base PCB to handle the OLED module.{{ :oled:oled_module_handling.jpg?400 |}}</WRAP>\\ {{ :oled:52-1020_oled-wechsel_schritt_3s.jpg?600 |}}
  - Disconnect the flat-ribbon cable connectors.\\ {{ :oled:flat_ribbon_cable_connectors.jpg?600 |}}
  - \\ <WRAP center round important 60%>**Important**\\ Before reassembling the main PCB to the housing, remove the protective foil on the OLED displays.</WRAP>\\ To reassemble the module, follow these instructions in reverse order.


/* ==== 52/RX modules ====

==== 52/MX modules ====

Erst rückfragen bei deu vor veröffentlichung - OFEN!!!! FIXME
  - Fader demontieren,
  - Plastikrahmen (der unteren Tasten - sind nur mit ablösbarem Silikon fixiert) demontieren,
  - Leiterplatten demontieren,
    - dazu Display Stecker mit Pinzette vorsichtig von der Seite entriegeln,
    - dazu Bolzen der Frontplatte ggf. mit kleiner Flachzange oder passendem Werkzeug halten damit die sich nicht beim Lösen der Schrauben der Leiterplatte drehen,
  - und legen die Frontplatte für ca. 10 Minuten in einen maximal 50 ... 60 Grad heißen Ofen (bitte zunächst an einem Exemplar testen und Parameter ggf. anpassen), das verflüssigt den Kleber etwas, die Displays lassen sich danach mit einer kleinen Flachzange leichter ablösen ohne die Folie zu beschädigen.

 */
/* Japan Mail vom Jörg.

Hinweis ab welcher TB 5 das Brightness dim eingebaut ist.

Q rm5200d support -> word und pdf

17.11.2016 Japan mail */