<- sx2:general|General information on Configuration ^ sx2:start|SX2 Configuration ^ sx2:system_settings|System Settings ->
======Hardware======

[{{ :sx2:sx2-hardware.png?nolink |//SX2Config Software - Hardware//}}]

On the ''Hardware'' page you can set which SX2 modules are connected to your system. 

===== Common Settings Area =====

In the ''Device name'' box, enter a distinctive device name for this SX2 mixing console.


===== Console Faders =====

In the drop-down menu, select the number of faders.

===== Core =====

Select your core type. (''52-7424'': 52/XC2 Core; ''52-1830'': 52/XS2 Core with integrated Multi I/O (Default))

  * ''Use MADI Module 52-7321'': If your XS2 core is equipped with a MADI module 52-7321, please select this check box to enable the inputs and outputs for the ''I/O Settings'' tab.
  * ''Use Gigabit Audio 52-7391'': If your XS2 core is equipped with a Gigabit Audio SFP Module, this enables the inputs and outputs in the ''I/O Settings'' tab. Gigabit Audio is useful e.g. to interlink with other DHD devices.
  * ''Use Dante module 52-7080'': If your 52/XS22 / 52/XC2 core is equipped with a 52-7080 internal Dante module.
  * ''Use AES67 module 52-7067'': If your 52/XS22 / 52/XC2 core is equipped with a 52-7067 internal AES67 module.

<WRAP center round info 60%>
**Note**\\  Because 52/XC2 and 52/XS2 cores only have one option slot for one internal audio over IP module, you can select either 52-7080 **or** 52-7067.
</WRAP>

The ''Configure'' buttons behind each option become available if global options for an I/O Module are available.

===== APC connections =====

On the correct APC port, select the I/O module / Device Link you connected to the hardware. Always begin with the highest APC port number available.

The ''Configure'' buttons behind each option become available if global options for an I/O Module are available.

<WRAP center round tip 80%>
**Tip**\\  When using older I/O Modules, they are not displayed by default. Go to ''Options''>''Configuration'' and select the ''Product Filter''-Tab. 

Activate {{:wiki:rot.png?nolink}} ''show discontinued products''. All Module types are now visible.
</WRAP>
==== for 52-7424 DSP cores ====

  * ''APC 8'': Select an I/O type or set the value to ''(none)''. Default is ''52-1335''.
  * ''APC 7'': Select an I/O type or set the value to ''(none)''. Default is ''(none)''.
  * ''APC 6'': Select an I/O type or set the value to ''(none)''. Default is ''(none)''.
  * ''APC 5'': Select an I/O type or set the value to ''(none)''. Default is ''(none)''.
  * ''APC 4'': Select an I/O type or set the value to ''(none)''. Default is ''(none)''.
  * ''APC 3'': Select an I/O type or set the value to ''(none)''. Default is ''(none)''.

==== for 52-1830 DSP I/O cores ====

  * ''APC 4'': Select an I/O type or set the value to ''(none)''. Default is ''52-1335''.
  * ''APC 3'': Select an I/O type or set the value to ''(none)''. Default is ''(none)''.
  * ''APC 2'': Select an I/O type or set the value to ''(none)''. Default is ''(none)''.
===== Console Preview =====

Shows a version of the console in the preview.