<- sx2:system_settings|System Settings ^ sx2:start|SX2 Configuration ^ sx2:console|Console -> ====== I/O Settings ====== On the ''I/O Settings'' page, you can configure different options for each input and output. Not all options are available for any input or output. [{{ :sx2:sx2-io-settings.png?nolink |//SX2Config Software - I/O Settings//}}] In the following tables, you can find the descriptions for these options. **Tip**\\ For more information on internal and external leveling, see [[tb8:level_adjust|Toolbox 8 Documentation / Level Adjust]]. ===== Inputs/Outputs area ===== ^ column ^ description ^ |Original Label|This column shows the internal label which is generated in that scheme: .| |Label|Individual Label, double-click on the label and change the current name.| |Stereo|Indicates if the signal is mono or stereo.| |Source|Shows the assigned audio/logic source for input and output.| |Mute|Shows, that a Mute Logic is assigned to an output.| ===== IOModule-X. - Audio Inputs area ===== ^ option ^ description ^ |Type of Signal|Shows the general signal type of the port.| |Enter Label|Enter a distinctive name for the selected input.| |Level Adjust|Choose the headroom for each input from the corresponding drop-down menu. The shown values always refer to the devices internal default level of **0 dBint**.| |Select M/S|Select, if the signal is mono or stereo.| |Sample Rate Converter|Select from the dropdown menu, if the sample rate converter is activated (''On'') or deactivated (''Off'') for this input.| |Add to Input Pool|Select this check box to make this signal available for a channel on the console| The following sections are only available if ''Add to Input Pool'' is checked. ==== Fader Start ==== ^ option ^ description ^ |Fader Start Level|Select a level, which sets the fader start logic to on.| |On Start|The fader start is only activated and deactivated by pushing the On/Off key, not by moving the fader.| |Auto Off|By closing the fader, the channel is automatically switched'' OFF'' (''ON'' key is deactivated).| ==== Advanced ==== ^ option ^ description ^ |Timer Reset|If this check box is selected, opening this fader will reset and start the ''Auto'' timer of the stopwatch.| ==== Channel Logics ==== ^ option ^ description ^ |Channel On Logic|Select a Logic Function from the ''Logic Sources'' window, which sets the channel to ON. You can choose, for example, a GPI to open a channel.| |Channel Off Logic|Select a Logic Function from the ''Logic Sources'' window, which sets the channel to OFF. You can choose, for example, a GPI to close a channel.| |Mute Condition Logic|Click ''Source'' to select a Logic source, that mutes the input, if the logic source becomes true.| ==== Fader Function Logics ==== ^ option ^ description ^ |Activate Fader Function |Enable fader function for this channel. Default value is ''off''. Fader Function correlates with key function ''fader function'' (See [[sx2:console#key_elements|Console - Key Elements]] for more information). Fader function keys can serve as a logical source, e.g. for ''Talk'' purposes. | |Lamp Source 1 | • If you have assigned the ''Fader Function'' key function to a key of a fader module, here you can select a logic source which causes the LED of this key to light up.\\ • The default logic source is the fader function of the selected fader channel itself (Fader Function/FF ). In this case, the key is lighting up when the fader function is active.\\ • To change the logic source, click Select, the Logic Sources window opens. Select the desired logic source and click Assign. Alternatively, you can double-click on the logic source or drag the logic source to the Source box.\\ • **Examples:** As talk key for clean feeds or as talk key for headphones, which are assigned to certain microphones (configuration via output functions), fader start on/off for play-out devices (configuration via logic function). | |Lamp Source 2 | • If you have assigned the ''Fader Function'' key function to a key of a fader module, here you can select a logic source which causes the LED of this key to light up.\\ • To change the logic source, click Select, the Logic Sources window opens. Select the desired logic source and click Assign. Alternatively, you can double-click on the logic source or drag the logic source to the Source box.\\ • If lamp source 1 is active, lamp source 2 will be ignored. If lamp source 1 is not active, lamp source 2 will be used. | ==== Preamp Default Values ==== ^ option ^ description ^ |Analog Gain|Default value for analog gain. **Note**\\ Some analog I/O cards do not provide all gain values| |P48V|Turn Phantom Power On/Off by default| ==== Mute Logics ==== ^ option ^ description ^ |Mute Logic 1,2|Here, you can define which mute logics are enabled when opening a fader. Mostly, this assignment is used to mute speakers when opening microphone channels. You can control up to two mute logics. To do this, select the corresponding check boxes. \\ To assign a mute logic to an output select the mute logic checkbox at a selected output on this tab.| ==== Selector Lists ==== ^ option ^ description ^ |Selector List 1|Select this check box to add this audio source to source list 1. This Source will be available in the monitor source list, which is assigned to the ''SEL'' key on 52-5614 central module.| |Selector List 2|Select this check box to add this audio source to source list 2. This Source will be available for monitoring in the ''Monitor 2'' list, which is available on the ''Monitor Selector'' {{:sx2:mon-sel.png?50|}} view of the TFT/Touch Display.| ===== IOModule-X. - Audio Outputs area ===== [{{ :sx2:sx2-audiotree.png?200|//SX2Config Software - Audio Sources//}}] ^ option ^ description ^ |Type of Signal|Shows the general signal type of the port.| |Enter Label|Enter a distinctive name for the selected output.| |Headroom|Choose the headroom for each output from the corresponding drop-down menu. The shown values always refer to the devices internal default level of **0 dBint**.| |Select M/S|Chose, if the signal is mono or stereo.| |Sample Rate Converter|Select from the dropdown menu, if the sample rate converter is activated (''On'') or deactivated (''Off'') for this output.| |Dithering|If you connect devices with a lower resolution of the digital signals to a DHD device, here you can define how the internal audio signal is to be dithered before leaving the digital output. With this function, the quality of the output signal can be improved. You can select ''16 bit'', ''20 bit'', ''''or ''Off'' (no dithering, preset value).| |Digital Out Mode|This option can adopt the values ''Pro'' (default value) or ''Consumer''.| |Source|You can assign an audio signal to a mono output. \\ Click the ''Source'' button, the ''Audio sources'' window opens. Select an audio source, and click'' Assign''.| |Left Source|You can assign an audio signal to the left channel of the selected output. \\ Click the ''Source'' button, the ''Audio sources'' window opens. Select an audio source, and click'' Assign''.| |Right Source|You can assign an audio signal to the right channel of the selected output. \\ Click the ''Source'' button, the ''Audio sources'' window opens. Select an audio source, and click'' Assign''.| |Direct ACI|Select this check box to enable volume control for the headphones via a potentiometer which is connected to an ACI.\\ This option is only available for headphone outputs. The ACI on D-sub port 1 is assigned to headphone 1 (HP1) and the ACI on D-sub port 2 is assigned to headphone 2 (HP2).| |Mute Logic 1|Select this check box to mute this output if a fader with one of the inputs with selected ''Mute Logic 1'' checkbox is opened.| |Mute Logic 2|Select this check box to mute this output if a fader with one of the inputs with selected ''Mute Logic 2'' checkbox is opened.| **Important**\\ When switching ''Digital Out Mode'' between ''Pro'' or ''Consumer'', following values are changed: ^Mode^Pro^Consumer^ ^Terminator|110 Ohm|75 Ohm| ^Output Voltage|5V|0.5V| ^Data Stream|Professional Bit Set|Consumer Bit Set| ===== IOModule-X. - General Purpose Inputs (GPI) area ===== ^ option ^ description ^ |Type of Signal|Shows the general signal type of the port.| |Enter Label|Enter a distinctive name for the selected input.| ===== IOModule-X. - General Purpose Inputs (GPO) area ===== ^ option ^ description ^ |Type of Signal|Shows the general signal type of the port.| |Enter Label|Enter a distinctive name for the selected input.| |Select Source|You can assign a logic source to the selected GPO. \\ Click the ''Source'' button, the ''Logic sources'' window opens. Select a logic source, and click'' Assign''.|