<- tb5:pgmroutingrules|PGM Routing Rules ^ tb5:start|Toolbox5 Software ^ tb5:snapshot_options|Snapshot Options ->


====== Operation Mode ======

Select the ''Operation Mode'' tab to adjust general settings for the currently selected device.

^area   ^option   ^description    ^
|PFL1 Options   |Mix   | •  Enables, that several channels can be simultaneously routed on PFL1. If it is not checked, activating PFL on one channel will deactivate an active PFL on another channel.     |
|:::|Reset   | •  If the fader of any channel in PFL mode gets opened (it does not matter if the opened channel belongs to PFL bus 1 or 2), all currently active PFL1 routings are reset.     |
|:::|Reset Channel   | •  If a channel is routed on PFL1 and you open its fader, the PFL1 routing of that channel is reset.     |
|:::|Return   | •  If a channel is routed on PFL1 and you open its fader, the PFL1 routing of that channel is reset. If you close the fader, the PFL routing is reactivated.      |
|:::|AFL when Fader On   | •  Toggles automatically the monitoring mode from PFL to AFL, if the fader of a channel is opened (Faderstart ON).     |
|PFL2 Options   |Mix   | •  Enables, that several channels can be simultaneously routed on PFL1. If it is not checked, activating PFL on one channel will deactivate an active PFL on another channel.     |
|:::|Reset   | •  If the fader of any channel in PFL mode gets opened (it does not matter if the opened channel belongs to PFL bus 1 or 2), all currently active PFL1 routings are reset.     |
|:::|Reset Channel   | •  If a channel is routed on PFL1 and you open its fader, the PFL1 routing of that channel is reset.     |
|:::|Return   | •  If a channel is routed on PFL1 and you open its fader, the PFL1 routing of that channel is reset. If you close the fader, the PFL routing is reactivated.      |
|:::|AFL   | •  Enable the AFL monitoring mode for PFL2. <wrap center info 80%> **Note**\\  Function only available in TB5 v7.4 </wrap>|
|:::|DJ PFL   | •  Allows predefined fader position via PFL2 for next Channel Start (alternating to 0)\\  • **Requires defined PFL2-Bus**\\  • **Resets predefined fader position after Fader Start**  |
|Bus Options   |PGM2 follows PGM1   | • The routings to program bus 2 follow automatically the routings to program bus 1. This does not work vice versa.  \\  • **Example:** You route a channel to program bus \\  1. This channel is automatically routed to program bus \\  2. If you disable the routing to program bus 2, the routing to program bus 1 remains.|
|Off Air Options   |"Fader Start On" blocks "Off Air" switch off   | •  Channels can only be routed from Off Air to On Air mode if the faders are closed (see also [[tb5:console#control_modules|Control Modules / Auto OffAir]]).     |
|:::|Switching "OffAir" off moves Fader to -∞ dB| • If "OffAir" is activated on the channel, the Fader moves to -∞ dB <wrap center info 80%> **Note**\\  Function only available in TB5 v7.4</wrap>|
|:::|Allow switching "Off Air" state when "Fader Start On"| • Ignores "OnAir"-protection of all channels and activates off air if pressed. <wrap center info 80%> **Note**\\  Function only available in TB5 v7.4</wrap>|
|Clean Feed Options   |On Preparation Reset   | •  If the channel is in preparation mode, the preparation mode is automatically disabled when you open the fader. Selecting the check box prevents the channel from switching back to preparation mode after closing the fader.     |
|Channel On Options   |Extend Channel On when   | •  This function corresponds with the key functions Channel ON (Ext), Channel OFF (Ext) and Channel ON/OFF (Ext). See function [[tb5:console#control_modules|Control Modules / Channel ON/OFF (Ext)]]\\ •  Click Select to assign a logic source that switches between the Channel ON/OFF functionality and Channel Start ON/OFF.     |
|Access On Options   |PreFader signal sent to selector   | •  In this list, all available selectors are shown.\\  •  Chose a selector in this list, to which the PFL signal is routed when Access key is pressed in a fader channel.     |