<- tb8:super_output_functions|Super Output Functions ^ tb8:start|Toolbox8 Software ^ tb8:surround_configuration#downmix_surround_source_or_pgm_bus_to_stereo_output|5.1 Downmix -> ====== Fixed Processing ====== To create and configure fixed processings, select ''/Audio/Fixed Processing'' in the project tree. Fixed processings are universally applicable, fixed DSP functions to route internal signals for example through limiters, compressors etc. In addition, sine generators can be configured. You can use every audio signal available on the internal TDM bus as input for a fixed processing: inputs, delays, mixing functions (summing busses, groups, Aux busses), pre-fader signals (fader channel after input processing), clean feeds (n-1 busses), monitor functions, fixed processing, output functions, super output functions and talk outputs. The output of each fixed processing is available as an audio source in the ''Audio Sources'' window. Fixed Processings are internally computed as stereo, but they also can be used mono. Mixing devices contain a variety of DSP functions by default. Additional enhanced processings require an additional license code that has to be ordered separately. [{{ :tb8:fixed_processing.png?nolink |//Fixed Processing, configuration of a limiter.//}}] **Important**\\ Fixed processings can not be adjusted or changed by the mixer interface! The settings can be made with the TB8 software or with the DSP control software of the DHD Operation Manager to be able to change the settings during the runtime. ===== Standard DSP functions ===== The following DSP functions are available for fixed processing: ^standard DSP functions^max. number per fixed processing^option/parameter^ |Limiter|1|1. **Threshold**: Threshold in the range -20 dBint to +20 dBint (in steps of 1 dB).\\ 2. **Release Time**: Release time in the range 3 dB/s to 20 dB/s (in steps of 1 dB/s).\\ • The attack time can not be adjusted, it is always set to ''quick''.| |T-Limiter|1|• Transient Limiter with 300µs signal pre-delay, that allows to preprocess the signal.\\ 1. **Threshold**: Threshold in the range -20 dBint to +20 dBint (in steps of 1 dB).\\ 2. **Release Time**: Release time in the range 3 dB/s to 20 dB/s (in steps of 1 dB/s).\\ 3. **Additional Options**: If you have configured a preemphasis, you can add this information here to adapt the working mode of the T-Limiter.| |Compressor|1|1. **Gain**: Output gain in the range of 0 dB to +30 dB (in steps of 1 dB).\\ 2. **Threshold.**: Threshold in the range -50 dBint to +10 dBint (in steps of 1 dB).\\ 3. **Ratio**: Ratio in the range of 1.0:1 to 5.0:1 (steps of 0.1).\\ 4. **Attack**: Attack time in the range of 0.2 ms to 50 ms (8 values).\\ 5. **Release**: Release time in the range of 0.05 s to 10 s (8 values).| |Expander|1|1. **Gain**: Output gain in the range of 0 dB to +30 dB (in steps of 1 dB).\\ 2. **Threshold.**: Threshold in the range -50 dBint to +10 dBint (in steps of 1 dB).\\ 3. **Ratio**: Ratio in the range of 1:1.0 to 1:5.0 (steps of 0.1).\\ 4. **Attack**: Attack time in the range of 0.2 ms to 50 ms (8 values).\\ 5. **Release**: Release time in the range of 0.05 s to 10 s (8 values).| |EQ|4|• Equalizer with up to 4 bands.\\ 1. **EQ Type**: EQ type can be toggled between Bell, Notch, Shelving High and Shelving Low.\\ 2. **Gain**: Gain in the range -15 dB to +15 dB (in steps of 0.25 dB). Option is ignored if EQ type **Notch** is selected.\\ 3. **Frequency**: Frequency in the range 22 Hz to 20000 Hz (60 fixed preset values).\\ 4. **Quality**: Quality in the range 0.1 octaves to 3.0 octaves (in steps of 0.1 octaves). Option is ignored if EQ type **Shelving Low/High** is selected.\\ • The toggling of the EQ type is **not** noiseless!| |Sine|1|• Sine generator.\\ 1. **Level**: Level in the range -80 dBint to +15 dBint (in steps of 1 dB).\\ 2. **Frequency**: Depending on the ''Frequency table selection'' Frequency in the range 22 Hz to 20000 Hz (terz; 60 fixed preset values) or the rows and columns 1 to 4 of the DTMF table (8 fixed preset values).\\ 3. **Frequency table selection**: Here you can choose the frequency scale for the frequency option above. Terz (standard frequencies of a 1/3-octave) or DTMF (dual-tone multi-frequency signaling).| |AGC (Automatic Gain Control)|1|1. **Velocity**: Control speed in the range 0.3 dB/s to 6.0 dB/s (in steps of 0.1 dB/s).\\ 2. **Gain**: Max. signal shift in the range 0 dB to 30 dB (in steps of 1 dB).\\ 3. **Level**: Set output level in the range -20 dBint to 20 dBint (in steps of 1 dB).\\ 4. **Threshold**: Freeze threshold of the AGC in the range -40 dBint to -20 dBint (in steps of 1 dB), for lower levels, the current or last value is recorded respectively.| |Sub Sonic|2|1. **Frequency**: Frequency in the range 22 Hz to 20000 Hz (60 fixed preset values).\\ • This subsonic filter is a 3rd order high pass filter (18 dB/octave). For other filter orders, please use the function **Var. LP/HP**. | |DeEsser|1|1. **Ratio**: Ratio in the range 1.0:1 to 4.0:1 (in steps of 0.1).\\ 2. **Threshold**: Threshold in the range 1.0 to 1.8 (in steps of 0.1).\\ 3. **Bandwidth**: Bandwidth in the range 0.2 to 0.5 (in steps of 0.1).| |DeEsser 2|1|1. **Frequency**: Frequency in the range 1000 Hz to 20000 Hz (28 fixed preset values).\\ 2. **Threshold**: Threshold in the range -40 dB to +10 dB (in steps of 1 dB). | |Var. LP/HP|2|• Variable filter, high pass or low pass up to 10th order.\\ 1. **Filter Type**: Filter type can be toggled between **HighPass** and **LowPass**.\\ 2. **Frequency**: Frequency in the range 22 Hz to 20000 Hz (60 fixed preset values).\\ 3. **Filter Order**: Filter order can be set between 1st order (6 dB/octave) and 10th order (60 dB/octave).\\ • The toggling of the type and filter order is **not** noiseless!| |Noise Gate|1|1. **Attenuation.**: Attenuation in the range 0 dB to 30 dB (in steps of 1 dB).\\ 2. **Threshold**: Threshold in the range -60 dBint to -10 dBint (in steps of 1 dB).\\ 3. **Attack**: Attack time in the range of 1.0 ms to 200 ms (8 values).\\ 4. **Release**: Release time in the range of 0.01 s to 2.0 s (8 values).| ===== Enhanced DSP functions ===== For special applications like sound processing for FM transmission you can configure special ''Enhanced DSP Functions''. These functions are enabled using one license code per DSP frame: ^enhanced DSP functions^available in^max. number per fixed processing^ |Enhancer|1|• Stereo Enhancer to improve the stereo sound.\\ 1. **Widening**: This option allows the widening of the stereo spread.\\ 2. **3D Effect**: Creates a stereoscopic effect by adding delayed signals with a latency between 0 ms (0%) and approx. 40 ms (100%).\\ 3. **3D Mix**: Controls the ratio of the existing signal and the signal with 3D effect. 0% means no 3D effect and at 100% only the signal with 3D effect is passing.\\ 4. **Release**: Because of the widening effect, it may happen that the correlation becomes negative. The enhancer Plug-In includes a correlation limiter, that automatically lowers the widening to avoid destructive cancellations. At 0% this limiter is always active. If you higher the release time, negative correlated signals are excepted for a while.| |90˚ Filter|1|• Mono creation without shifting the medium frequencies.| |Profanity Delay|1|See [[#profanity_delay|Profanity Delay]]| |Loudness AGC|1|• Automatic Gain Control, triggered by loudness\\ 1. **Velocity**: Control speed in the range 0.1 LU/s to 6.0 LU/s (in steps of 0.1 dB/s).\\ 2. **Gain**: Max. signal shift in the range 0 dB to 30 dB (in steps of 1 dB).\\ 3. **Level**: Set output level in the range -20 LU to 20 LU (in steps of 1 LU).\\ 4. **Threshold**: Freeze threshold of the Loudness AGC in the range -60 LU to 0 LU (in steps of 1 LU), for lower levels, the current or last value is recorded respectively.| |Pink Noise Generator|1|Generates pink noise.| |Delay 1s|1|**Delay time**: Adjustable between 0 s and 1 s in steps of 1 ms.| |Delay 10 s|1|**Delay time**: Adjustable between 0 s and 10 s in steps of 1 ms.| |Hinz Generator|1|• Sound signal for traffic broadcast recognition (Germany only).| |Profanity Delay 2|1|See [[#profanity_delay|Profanity Delay]]| To use the extended functions, you have to order the software license **52-8581 Enhanced DSP Fixed Processing**. To be able to adjust the settings during the runtime, you also need the **52-8565 DSP Control Software**, which has to be ordered additionally. ===== Configuring Fixed Processing ===== To create and configure a fixed processing, follow these steps: - To create a new fixed processing, in the ''Fixed Processings'' area, click ''Add''. - To change the name for a selected fixed processing, in the ''Edit Fixed Processing'' area, enter name in the ''Label'' box. This label can be up to 16 digits long. - To select an audio source as input for the processing, click ''Select''. The ''Audio Sources'' window opens. - In the ''Audio Sources'' window, select the desired audio source and click ''Assign''. Alternatively, you can double-click on the audio source or drag it to the ''Source'' box. **Note**\\ If you use a generator function for the fixed processing, you don't need to assign an audio source. If an audio source is assigned anyway, it will be ignored! - If you select the ''Stereo'' check box, the subsequent channel is selected automatically, in most cases the right channel of a stereo signal. Apart from this, the fixed processing is also shown as a stereo signal in the ''Audio Sources'' window. - Decide how to proced after Firmware Reset/Start: Use parameters from Toolbox or from Device. The parameters from Toolbox are the parameters which are set by default in the TB8 Config file. The parameters from the device are the values which are maybe changed by a DSP control software. - To assign a DSP function to a selected fixed processing, select the desired DSP function in the Available Functions list and click {{:tb5:links-pfeil.png?28x27}}. Alternatively, you can double-click on the desired DSP function or drag it to the ''Selected DSP Functions'' list. - To change the parameter of a DSP function, in the ''Selected DSP Functions'' area, double-click on it, a parameter window opens. In this window the respective parameters for each DSP function are shown. All levels generally relate to the internal reference level of 0 dBint. For example, if a limiter at a digital output configured with a headroom of 9 dB should trigger exactly at the maximum level of 0 dBFS, you have to set them to 9 dBint. **Tip**\\ For more information on levels see [[tb8:level_adjust|Level Adjust]] **Note**\\ You can assign up to 10 DSP functions to a single fixed processing. For the configuration of a fixed processing, you have the following options: * To remove a DSP function from the ''Selected DSP-Functions'' list, select the DSP function and click {{:tb5:rechts-pfeil.png?28x27}}. Alternatively, you can also drag the DSP function from the ''Selected DSP Functions'' list to the ''Available Functions'' list. * The order of the entries in the ''Selected DSP Functions'' list (top to bottom) also indicates the signal path. You can change this order by dragging a DSP function to a new position in the list. * To remove a selected fixed processing from the ''Fixed Processings'' list, click ''Remove''. **Important**\\ When creating the fixed processings, keep in mind that they affect the DSP load of the whole system. Therefore, do not create more fixed processings than necessary to save the DSP resources for other applications. ==== Profanity Delay ==== **Important**\\ The ''Profanity Delay'' is available for all 52/XC, 52/XC2, 52/XD, 52/XD2, 52/XS and 52/XS2 Cores.\\ ''Profanity Delay 2'' is available for all 52/XC2, 52/XD2 and 52/XS2 Cores. * The Hardware needs the license 52-8581 **Enhanced DSP Processing** (necessary for all Cores). * 52/XS2 and 52/XS Core hardware additionally requires the license 52-1950 XS Core extended feature upgrade to be able to configure the function and the push buttons **Note**\\ ''Profanity Delay 2'' Requires minimum Firmware version 8.2.3 / Toolbox8 8.2.2. Profanity delay provides a delay time between 1 and 100 seconds with parameters for the minimum pitch and the dump amount. There are two different profanity delay plugins available: * ''Profanity delay'' provides a delay time between 1 and 30 seconds with 3 predefined dump times (full / half / third) * ''Profanity delay 2'' provides a delay time between 0 and 100 seconds with flexible dump time. To configure the Profanity delay in the TB8 software, follow these steps: 1. In the ''project'' area, select ''/Audio/Fixed Processing''. Assign the designated profanity delay to a ''Fixed Processing'' and assign, for example ''PGM1'' as audio source. [{{ :tb8:profanity1.png?nolink |//Profanity delay as Fixed Processing//}}] [{{ :tb8:profanity2.png?nolink|//Profanity delay parameters window (for Profanity Delay 1)//}}] 2. In the ''Select DSP Functions'' area and double-click on ''Profanity Delay'' or ''Profanity Delay 2''. The ''Profanity Delay parameters'' window opens. * In the ''Delay'' area, select a profanity delay time between 1 and 30 seconds. * In the ''Minimum Pitch'' area, select the pitch for fade in and fade out (lower pitch is almost inaudible, but takes longer time). Can be between 0.8% to 12.5%. * In the ''Dump Amount'' area, select if the ''full (1)'' delay memory, ''half (1/2)'' of the delay memory or a ''third (1/3)'' of the delay memory will be dumped when pressing the dump push button on the control surface. 3. In the ''project'' area, select ''//Console''. On the ''Keys'' tab, select a push button in a central control module to assign one of the profanity delay key functions from the ''Key Functions'' window. You can also use buttons on the TFT/Touch display. For details on Key Functions, see [[tb8:console#profanity_delay|Console/Profanity Delay]]. [{{ :tb8:profanity3.png?nolink |//Assign profanity delay key functions to push buttons//}}] 4. You can now use the profanity delay Fixed Processing like normal audio on the TDM Bus. You can use it with an Output Function or route it directly to an Output. **Tip**\\ If Profanity Delay detects silence, it fills the buffer faster. === Display Profanity Delay State on TFTs === **Note**\\ Requires minimum Firmware version 8.1.35 / Toolbox8 8.1.26. [{{ :tb8:profanity_tft.png|//Profanity Delay TFT Elements.//}}] Profanity delay key functions are also available for TFT buttons. Also, two additional label functions are available: * ''Porfanity Delay State (s)'': Shows the buffered audio time (current fill state in seconds). * ''Profanity Delay Max. Delay'': Shows the maximum amount configured in the profanity delay settings. For details on Label Elements, see [[tb8:element_configuration#label_element|Label Element]].