<- tb9:switchable_inserts|Switchable Inserts ^ tb9:start|Toolbox9 Software ^ tb9:super_output_functions|Super Output Functions ->

====== Output Functions ======

To configure output functions, in the project tree, select ''<Device>/<Audio>/Output Functions''.

Output functions are universally applicable DSP functions for switching, level changing, talkback and summation applications. Often, these are used directly before an audio signal output. This is where the name comes from: **output function.**

Every output function has two audio inputs, ''Source 1'' and ''Source 2''. These inputs are summed. You can influence them by two corresponding level values. The special thing about this is the following: Both, the sources of the input signals as well as their levels can be changed according to logic conditions. The output signal of an output function itself is available as an audio source on the TDM bus. Using this method, the most different applications can be realised. 

In the following figure, in the ''Edit Output Function'' area, you see an example of a configured output function: 

[{{ tb9_outputfunctions.png?1000&nolink |//Output functions, selecting audio sources.//}}]

The following signals can be used as input signals (''Source 1'' and ''Source 2'') for output functions:

  * Audio channels available on the internal TDM bus: inputs, delays, mixing functions (summing busses, groups, Aux busses), pre-fader signals (fader channels after input processing), clean feeds (n-1 busses), monitor functions, fixed processing, output functions, super output functions and talk outputs.

  * You can set the levels (''Level'') from -∞ (off), -100 dB up to +20 dB in steps of 1 dB. Further more, in addition to this fixed amplification value, the value of a potentiometer can be added and the phase position of the signal can be rotated by 180 degrees.

An output function can have the preset logic condition ''Default'' and up to 9 further logic conditions. Each of them is shown in the list in the ''Edit Output Function'' area. Each of them is shown as a row in that list. There you can assign other input signals and level values. 

The logic condition ''Default'' is always in the top line and always active if none of the configured conditions below is active (logically true). 

As logic conditions in the ''Condition'' column you can use all logic sources that are available in the ''Logic Sources'' window.

The priority of the logic conditions decreases from top to bottom. So a condition is only used if all conditions above it are inactive. 

For the example in the figure, this means (viewed from bottom to top): 

  * If the logic source ''CR_MONO'' is activated (CR_MONO key pressed), the fourth line is executed - the monitor paths ''CR L'' and ''CR R'' get to the output of the output function ''CR LSP 1L'' as a mono summation with an attenuation of -3 dB. 

  * If at the same time with ''CR_MONO'' the logic condition ''CR_RR'' (CR_RR key pressed) is active, the third line is executed - the monitor path ''CR R'' gets to the output of the output function ''CR LSP 1L''.

  * If at the same time ''CR_MONO'' and/or ''CR_RR'' and the logic condition ''CR_LL'' (CR_LL key pressed) is active, the second line is executed - the monitor path ''CR L'' is routed to the output of the output function ''CR LSP 1L''.

  * If none of the just mentioned logic conditions is active, the first line is executed - the monitor path ''CR L'' is routed to the output of the output function ''CR LSP 1L''.

If no other logic condition is programmed, always the first line ''Default'' is active.

Output functions are mono at the inputs and at the outputs. So for stereo signals, the left and the right channels have to be programmed separately!

To create a new output function, click ''Add''. To delete a selected output function, click ''Remove''. You can also right-click in the ''Output Function'' list to add or remove an output function. 

===== Edit Output Functions =====

In the ''Edit Output Functions'' area, you can configure the output function which is selected in the ''Output Functions'' list. 

To configure a created output function, follow these steps: 

1.	Enter a distinctive name for the output function in the ''Label'' box. Please note that the name should be comprehensive because up to 120 output functions can be available per device. 


2.	Click ''Add'' to insert a new condition row. Now select the new condition row. Definiton fields (''Condition'', ''Source'', ''Potentiometer'' and ''Level'') are now displayed. For first row, condition is always default and therefore not clickable.

3.	Click ''Condition'' to open the ''Logic Sources'' window. 

4.	In the ''Logic Sources'' window, select the desired logic source and click ''Assign''. Alternatively, you can double-click on the logic source or drag it to the ''Condition'' column of the list. The first row of the list always contains the condition ''Default'' and can not be changed. 

5.	Assign the first audio sources to the selected condition row. To do this, click ''Select'' in the ''Source 1'' Section to open the ''Audio Sources'' window.

6.	In the ''Audio Sources'' window, select the desired audio source, click ''Assign''.

7.	Adjust the level using the potentiometer in the ''Source 1'' Section. To change a level, click and hold the potentiometer button. If you move the cursor to the left or the right holding the mouse button, you can change the level. Alternatively, you can click on the button, hold the mouse button and change the value using the following keys: 

|+1 dB steps|''right arrow'' key or ''up arrow'' key|
|-1 dB steps|''left arrow'' key or ''down arrow'' key|
|Off|''Pos 1''|
|+20 dB|''End''|
|+5% steps (+6 dB)|''Page up''|
|-5% steps (-6 dB)|''Page down''|

7.	To rotate the phase position of the selected audio source by 180 degrees, select the'' Phase Reverse'' check box.

8.	Select a potentiometer, the level value of which becomes valid in addition to the level value already configured. For example, if you have set the level of the audio source to -3 dB, and the selected potentiometer is set to -15 dB, in total, the signal is attenuated to $-15 dB + (-3 dB) = -18 dB$. Select the desired potentiometer or select ''(none)'' if you do not want to use a potentiometer. (See also [[tb9:Potentiometer|Potentiometer – Assigning Potentiometers]])

9.	To assign a second audio sources to the selected condition row, do the same in ''Source 2'' section.

To configure the output functions, please note the following hints: 

  * To delete a complete condition row, select the desired row and click ''Remove Source''. 
  * Select a condition row and right-click on it to access the options ''Add Source'', ''Condition'', ''Source 1'', ''Source 2'' and ''Remove Source''. Further on, in the contextual menu, you can set the level of ''Source 1'' and ''Source 2'' directly to ''0 dB'' or ''Off''.
  * To configure the condition and the audio sources for the selected row directly, double-click the corresponding column in the list.
  * Drag condition rows on a new position in the list to change its priority.
  * You can re-ordered output functions by drag and drop
  * Cut, Copy and Paste for Output Functions as well as for selected Conditions are available
  * New Output Functions context menu option: "Add right Ch OF from this" - if the "left" channel was already programmed this function will automatically add the "right" channel Output Function.

==== Output Function priority | Minimum Toolbox v9.0.4 & FW 9.0.2 ====

By using low priority output functions you can raise the maximum of 120 output functions to a maximum of 240.

<WRAP center round info 80%>
**Note**\\  License 52-8581 Enhanced DSP Processing and a device capable of 120 high priority output functions (see [[installation:functional_range_of_cores_fw9]]) required.
</WRAP>
<WRAP center round info 80%>
**Note**\\  Minimum Toolbox v9.0.4 & FW 9.0.2 required. 
</WRAP>

**High priority output functions** continue to be the default output functions for time critical applications. 

**Low priority output functions** can beused to save processing capacity and allow to have more output functions. Low priority output functions work in the same way as high priority output functions but are processed slower. This means that latency between triggering a condition and switching sources can be significantly higher but could be useful for many non-time critical applications such as routing lines or selecting monitor sources.

For example: if you want to mute your monitor speakers when a microphone channel is open you should use high priority output functions as the low priority output functions could cause a short audio feedback before the monitor speakers are muted.

Each low priority function allows to have another low priority function. If you only use low priority output functions you can have up to 240. If you only use high priority output functions you can have up to 120 output functions. (Ratio 1:2)\\
For example: if you have 60 high priority output functions, you can have 120 low priority output functions. That is a total of 180 output functions.