Table of Contents
Specifications of Audio Inputs and Outputs
52-7111A - XC Digital In/Out/GPIO Module, 8 ch.
General Information
- 4 AES3/EBU/SPDIF inputs, XLR3 female, input sample rate converters, 24 bit
- 4 AES3/EBU/SPDIF outputs, XLR3 male, output sample rate converters, 24 bit
- 4 general purpose inputs, isolated
- 4 general purpose outputs, isolated
- 2 DSub-9 connectors for GPIOs
Digital Inputs
| input impedance: | 110 Ohm (AES3/EBU) or 75 Ohm (S/PDIF) | ||
| input sensitivity: | > 200mV | ||
| input sample rate converters (SRC): | yes, with bypass mode (switchable by configuration software) | ||
| SRC input sampling frequency range: | 28 kHz … 195 kHz | ||
| frequency response | < 0.01 dB | ||
| dynamic range (SRC off): | > 144 dB (unweighted) | ||
| signal to noise ratio (SRC off): | > 144 dB (unweighted) | ||
| THD+N (SRC on, 44.1 kHz to 48 kHz): | < -130 dB / 0.00003% (-1 dBFS test signal) | ||
| max. input jitter: | > 40 ns (at 48 kHz), > 0.25 UI | ||
| supported standards: | AES3/EBU or S/PDIF (switchable by configuration software) | ||
Digital Outputs
| output impedance: | 110 Ohm (AES/EBU) or 75 Ohm (S/PDIF) | ||
| output level: | 3.4 V (into 110 Ohm load) | ||
| dynamic range (24 bit, dither off): | > 144 dB (unweighted) | ||
| signal to noise ratio (SRC off): | > 144 dB (unweighted) | ||
| THD+N (SRC on, 44.1 kHz to 48 kHz): | < -130 dB / 0.00003% (-1 dBFS test signal) | ||
| dither: | off, 16, 20 bit (switchable by configuration software) | ||
| jitter: | < 2 ns (peak) | ||
| supported standards: | AES3/EBU or S/PDIF (switchable by configuration software) | ||
General Purpose Inputs / Outputs (GPI/GPO)
| 4 GPIs (optocoupler, isolated): | external ON voltage 5 V … 24 V (DC) without external resistor, internal current limiter to 4 mA current for ON, OFF voltage: 0 V … + 1.5 V | ||
| 4 GPOs (electronic relay, isolated): | maximum rated current: 0.2 A (resettable fuse), maximum peak switched voltage: 30 V DC | ||
Further Information
| power consumption: | 3 W | ||
| connector style: | audio input: XLR-3 female audio output: XLR-3 male GPIO: SubD-9 female |
||
Note
All values are typical values.
52-7112A - XC Digital In/Out/GPIO Module, 8 ch.
General Information
- 4 AES3/EBU/SPDIF inputs, XLR3 female, input sample rate converters, 24 bit
- 4 AES3/EBU/SPDIF outputs, XLR3 male, output sample rate converters, 24 bit
- 4 general purpose inputs, isolated
- 4 general purpose outputs, isolated
- 2 DSub-9 connectors for GPIOs
Digital Inputs
| input impedance: | 110 Ohm (AES3/EBU) or 75 Ohm (S/PDIF) | ||
| input sensitivity: | > 200mV | ||
| input sample rate converters (SRC): | yes, with bypass mode (switchable by configuration software) | ||
| SRC input sampling frequency range: | 28 kHz … 108 kHz | ||
| frequency response | < 0.01 dB | ||
| dynamic range (SRC off): | > 144 dB (unweighted) | ||
| signal to noise ratio (SRC off): | > 144 dB (unweighted) | ||
| THD+N (SRC on, 44.1 kHz to 48 kHz): | < -130 dB / 0.00003% (-1 dBFS test signal) | ||
| max. input jitter: | > 40 ns (at 48 kHz), > 0.25 UI | ||
| supported standards: | AES3/EBU or S/PDIF (switchable by configuration software) | ||
Digital Outputs
| output impedance: | 110 Ohm (AES/EBU) or 75 Ohm (S/PDIF) | ||
| output level: | 3.4 V (into 110 Ohm load) | ||
| output sample rate converters (SRC): | yes (slaved to related input), with bypass mode (switchable by configuration software) | ||
| SRC output sampling frequency range: | 28 kHz … 54 kHz | ||
| dynamic range (24 bit, dither off): | > 144 dB (unweighted) | ||
| signal to noise ratio (SRC off): | > 144 dB (unweighted) | ||
| THD+N (SRC on, 44.1 kHz to 48 kHz): | < -130 dB / 0.00003% (-1 dBFS test signal) | ||
| dither: | off, 16, 20 bit (switchable by configuration software) | ||
| jitter: | < 2 ns (peak) | ||
| supported standards: | AES3/EBU or S/PDIF (switchable by configuration software) | ||
General Purpose Inputs / Outputs (GPI/GPO)
| 4 GPIs (optocoupler, isolated): | external ON voltage 5 V … 24 V (DC) without external resistor, internal current limiter to 4 mA current for ON, OFF voltage: 0 V … + 1.5 V | ||
| 4 GPOs (electronic relay, isolated): | maximum rated current: 0.2 A (resettable fuse), maximum peak switched voltage: 30 V DC | ||
Further Information
| power consumption: | 3 W | ||
| connector style: | audio input: XLR-3 female audio output: XLR-3 male GPIO: SubD-9 female |
||
Note
All values are typical values.
52-7170A - XC Quad 3G/HD/SD-SDI De-embedder
General Information
- 4 x 3G/HD/SD SDI De-embedders, each:
- Input and loop through BNC connector
- De-embedder for 2 audio groups, 8 ch.
- Sample rate converters, 8 channels
- Selectable audio groups 1/2 or 3/4
- 4 general purpose inputs, isolated
- 4 general purpose outputs, isolated
Digital Video Input
| cable type: | coaxial cable, Serial Digital Interface (adaptive cable equalizer included) | ||
| rate: | operation at 2.97 Gb/s, 2.97/1.001 Gb/s, 1.485 Gb/s, 1.485/1.001 Gb/s and 270 Mb/s | ||
| supported standards: | SMPTE 425M (Level A and Level B), 424M, 260M, 259M-C, 274M, 296M, 125M, 292M, ITU-R BT.656
Download |
||
| function: | Audio de-embedder for 8 channels of 48 kHz audio | ||
| sample rate converter of de-embedder: | yes, with bypass mode (switchable by configuration software) | ||
| frequency response: | < 0.01 dB | ||
| dynamic range (SRC off): | > 144 dB (unweighted, 24 bit embedded audio data) | ||
| signal to noise ratio (SRC off): | > 144 dB (unweighted) | ||
| THD+N (SRC on, 48 kHz to 48 kHz): | < -130 dB / 0.00003% (-1 dBFS test signal) | ||
Loop-Through Digital Video Output
| output signal: | reclocked digital video input | ||
| cable type: | coaxial cable, Serial Digital Interface | ||
General Purpose Inputs / Outputs (GPI/GPO)
| 4 GPIs (optocoupler, isolated): | external ON voltage 5 V … 24 V (DC) without external resistor, internal current limiter to 4 mA current for ON, OFF voltage: 0 V … + 1.5 V | ||
| 4 GPOs (electronic relay, isolated): | maximum rated current: 0.2 A (resettable fuse), maximum peak switched voltage: 30 V DC | ||
Further Information
| power consumption: | 5.8 W | ||
| connector style: | BNC | ||
| printed circuit board (PCB) revision for this specifications: | 1 | ||
Note
All values are typical values.
52-7172A - XC Dual Embedder/De-embedder
General Information
- 2 x 3G/HD/SD SDI De-embedders and 2 x HD/SD SDI Embedders, each:
- In, 2x loop through, Out BNC connectors – for 2 audio groups, 8 ch., SRCs
- Selectable audio groups 1/2 or 3/4
- minimum firmware 7.4.10
- 4 general purpose inputs, isolated
- 4 general purpose outputs, isolated
Digital Video Input
| cable type: | coaxial cable, Serial Digital Interface (adaptive cable equalizer included) | ||
| rate: | operation at 2.97 Gb/s, 2.97/1.001 Gb/s, 1.485 Gb/s, 1.485/1.001 Gb/s and 270 Mb/s | ||
| supported standards: | SMPTE 425M (Level A and Level B), 424M, 260M, 259M-C, 274M, 296M, 125M, 292M, ITU-R BT.656; 272M; 299M | ||
| function: | Up to eight channels (two audio groups) of serial digital audio may be extracted from the video data stream, in accordance with SMPTE 272M-C and SMPTE 299M. | ||
| sample rate converter of de-embedder: | yes, with bypass mode (switchable by configuration software) | ||
| frequency response: | < 0.01 dB | ||
| dynamic range (SRC off): | > 144 dB (unweighted, 24 bit embedded audio data) | ||
| signal to noise ratio (SRC off): | > 144 dB (unweighted) | ||
| THD+N (SRC on, 48 kHz to 48 kHz): | < -130 dB / 0.00003% (-1 dBFS test signal) | ||
Digital Video Output
| cable type: | coaxial cable, Serial Digital Interface (adaptive cable equalizer included) | ||
| rate: | operation at 2.97 Gb/s, 2.97/1.001 Gb/s, 1.485 Gb/s, 1.485/1.001 Gb/s and 270 Mb/s | ||
| supported standards: | SMPTE 425M (Level A and Level B), 424M, 260M, 259M-C, 274M, 296M, 125M, 292M, ITU-R BT.656; 272M; 299M | ||
| function: | In accordance with SMPTE ST 272 and SMPTE ST 299, up to eight channels (two audio groups) of serial digital audio may be embedded into the video data stream. 16, 20 and 24-bit audio formats are supported at 48kHz synchronous for SD modes and 48kHz synchronous or asynchronous in HD, 3Gb/s modes. | ||
| sample rate converter of embedder: | yes, with bypass mode (switchable by configuration software) | ||
| frequency response: | < 0.01 dB | ||
| dynamic range (SRC off): | > 144 dB (unweighted, 24 bit embedded audio data) | ||
| signal to noise ratio (SRC off): | > 144 dB (unweighted) | ||
| THD+N (SRC on, 48 kHz to 48 kHz): | < -130 dB / 0.00003% (-1 dBFS test signal) | ||
Loop-Through Digital Video Output
| output signal: | reclocked digital video input | ||
| cable type: | coaxial cable, Serial Digital Interface | ||
General Purpose Inputs / Outputs (GPI/GPO)
| 4 GPIs (optocoupler, isolated): | external ON voltage 5 V … 24 V (DC) without external resistor, internal current limiter to 4 mA current for ON, OFF voltage: 0 V … + 1.5 V | ||
| 4 GPOs (electronic relay, isolated): | maximum rated current: 0.2 A (resettable fuse), maximum peak switched voltage: 30 V DC | ||
Further Information
| power consumption: | 5.8 W | ||
| connector style: | BNC | ||
| printed circuit board (PCB) revision for this specifications: | 1 | ||
Known restriction: Time code will not be transferred between deembedder and embedder, this can't be fixed as it is a behavior of the Gennum embedder, deembedder chipsets.
Note
All values are typical values.
52-7222A - XC Analog In/Out/GPIO Module, 4 ch.
General Information
- 4 analog line inputs, 18dBu max., XLR3 female, el. balanced, 24 bit
- 4 analog line outputs, 18dBu max., XLR3 male, el. balanced, 24 bit
- 4 general purpose inputs, isolated
- 4 general purpose outputs, isolated
- 2 DSub-9 connectors for GPIOs
A/D Converter
| max. input level: | 18 dBu (balanced) | ||
| input impedance: | 15 kOhm | ||
| frequency response: | < 0.03 dB | ||
| THD+N: | < -90 dB / 0.003% (-1 dBFS, +17 dBu) | ||
| crosstalk: | < -100 dB | ||
| dynamic range: | > 111 dB (A-weighted) | ||
| signal to noise ratio: | > 109 dB (unweighted) | ||
| common mode rejection: | > 60 dB | ||
| converter technology: | 24 bit, oversampling sigma-delta | ||
D/A Converter
| max. output level (phones, single ended): | 18 dBu (balanced) | ||
| output impedance: | 25 Ohm | ||
| minimum load (outputs short circuit protected): | 600 Ohm | ||
| frequency response: | < 0.05 dB | ||
| THD+N: | < -90 dB / 0.003% (-1 dBFS, +17 dBu) | ||
| crosstalk: | < -90 dB | ||
| dynamic range: | > 109 dB (A-weighted) | ||
| signal to noise ratio: | > 107 dB (unweighted) | ||
| DC offset voltage: | < 10 mV | ||
| common mode rejection (output impedance): | > 60 dB | ||
| common mode rejection (output voltage): | > 40 dB | ||
| converter technology: | 24 bit, oversampling sigma-delta | ||
General Purpose Inputs / Outputs (GPI/GPO)
| 4 GPIs (optocoupler, isolated): | external ON voltage 5 V … 24 V (DC) without external resistor, internal current limiter to 4 mA current for ON, OFF voltage: 0 V … + 1.5 V | ||
| 4 GPOs (electronic relay, isolated): | maximum rated current: 0.2 A (resettable fuse), maximum peak switched voltage: 30 V DC | ||
Further Information
| power consumption: | 4.2 W | ||
| sample frequency: | 48 kHz or 44.1 kHz (automatically synchronised to the configured device system sample frequency) | ||
| connector style: | audio input: XLR-3 female audio output: XLR-3 male GPIO: SubD-9 female |
||
Note
All values are typical values.
52-7223A - XC Analog In/Out/GPIO Module, 4 ch.
General Information
- 4 analog line inputs, 24dBu max., XLR3 female, el. balanced, 24 bit
- 4 analog line outputs, 24dBu max., XLR3 male, el. balanced, 24 bit
- 4 general purpose inputs, isolated
- 4 general purpose outputs, isolated
- 2 DSub-9 connectors for GPIOs
A/D Converter
| max. input level: | 24 dBu (balanced) | ||
| input impedance: | 15 kOhm | ||
| frequency response: | < 0.03 dB | ||
| THD+N: | < -90 dB / 0.003% (-1 dBFS, +23 dBu) | ||
| crosstalk: | < -100 dB | ||
| dynamic range: | > 111 dB (A-weighted) | ||
| signal to noise ratio: | > 109 dB (unweighted) | ||
| common mode rejection: | > 60 dB | ||
| converter technology: | 24 bit, oversampling sigma-delta | ||
D/A Converter
| max. output level (phones, single ended): | 24 dBu (balanced) | ||
| output impedance: | 25 Ohm | ||
| minimum load (outputs short circuit protected): | 600 Ohm | ||
| frequency response: | < 0.05 dB | ||
| THD+N: | < -90 dB / 0.003% (-1 dBFS, +23 dBu) | ||
| crosstalk: | < -90 dB | ||
| dynamic range: | > 109 dB (A-weighted) | ||
| signal to noise ratio: | > 107 dB (unweighted) | ||
| DC offset voltage: | < 10 mV | ||
| common mode rejection (output impedance): | > 60 dB | ||
| common mode rejection (output voltage): | > 40 dB | ||
| converter technology: | 24 bit, oversampling sigma-delta | ||
General Purpose Inputs / Outputs (GPI/GPO)
| 4 GPIs (optocoupler, isolated): | external ON voltage 5 V … 24 V (DC) without external resistor, internal current limiter to 4 mA current for ON, OFF voltage: 0 V … + 1.5 V | ||
| 4 GPOs (electronic relay, isolated): | maximum rated current: 0.2 A (resettable fuse), maximum peak switched voltage: 30 V DC | ||
Further Information
| power consumption: | 6.1 W | ||
| sample frequency: | 48 kHz or 44.1 kHz (automatically synchronised to the configured device system sample frequency) | ||
| connector style: | audio input: XLR-3 female audio output: XLR-3 male GPIO: SubD-9 female |
||
Note
All values are typical values.
52-7224A - XC Analog In/Out/GPIO Module, 4 ch.
General Information
- 4 analog line inputs, 18 or 24dBu max., XLR3 female, el. balanced, 24 bit
- 4 analog line outputs, 18 or 24dBu max., XLR3 male, el. balanced, 24 bit
- 4 general purpose inputs, isolated
- 4 general purpose outputs, isolated
- 2 DSub-9 connectors for GPIOs
A/D Converter, 18 dBU mode
| max. input level: | 18 dBu (balanced) | ||
| input impedance: | 15 kOhm | ||
| frequency response: | < 0.03 dB | ||
| THD+N: | < -90 dB / 0.003% (-1 dBFS, +17 dBu) | ||
| crosstalk: | < -100 dB | ||
| dynamic range: | > 111 dB (A-weighted) | ||
| signal to noise ratio: | > 109 dB (unweighted) | ||
| common mode rejection: | > 60 dB | ||
| converter technology: | 24 bit, oversampling sigma-delta | ||
D/A Converter, 18 dBu mode
| max. output level (phones, single ended): | 18 dBu (balanced) | ||
| output impedance: | 25 Ohm | ||
| minimum load (outputs short circuit protected): | 600 Ohm | ||
| frequency response: | < 0.05 dB | ||
| THD+N: | < -90 dB / 0.003% (-1 dBFS, +17 dBu) | ||
| crosstalk: | < -90 dB | ||
| dynamic range: | > 109 dB (A-weighted) | ||
| signal to noise ratio: | > 107 dB (unweighted) | ||
| DC offset voltage: | < 10 mV | ||
| common mode rejection (output impedance): | > 60 dB | ||
| common mode rejection (output voltage): | > 40 dB | ||
| converter technology: | 24 bit, oversampling sigma-delta | ||
A/D Converter, 24 dBu mode
| max. input level: | 24 dBu (balanced) | ||
| input impedance: | 15 kOhm | ||
| frequency response: | < 0.03 dB | ||
| THD+N: | < -90 dB / 0.003% (-1 dBFS, +23 dBu) | ||
| crosstalk: | < -100 dB | ||
| dynamic range: | > 111 dB (A-weighted) | ||
| signal to noise ratio: | > 109 dB (unweighted) | ||
| common mode rejection: | > 60 dB | ||
| converter technology: | 24 bit, oversampling sigma-delta | ||
D/A Converter, 24 dBu mode
| max. output level (phones, single ended): | 24 dBu (balanced) | ||
| output impedance: | 25 Ohm | ||
| minimum load (outputs short circuit protected): | 600 Ohm | ||
| frequency response: | < 0.05 dB | ||
| THD+N: | < -90 dB / 0.003% (-1 dBFS, +23 dBu) | ||
| crosstalk: | < -90 dB | ||
| dynamic range: | > 109 dB (A-weighted) | ||
| signal to noise ratio: | > 107 dB (unweighted) | ||
| DC offset voltage: | < 10 mV | ||
| common mode rejection (output impedance): | > 60 dB | ||
| common mode rejection (output voltage): | > 40 dB | ||
| converter technology: | 24 bit, oversampling sigma-delta | ||
General Purpose Inputs / Outputs (GPI/GPO)
| 4 GPIs (optocoupler, isolated): | external ON voltage 5 V … 24 V (DC) without external resistor, internal current limiter to 4 mA current for ON, OFF voltage: 0 V … + 1.5 V | ||
| 4 GPOs (electronic relay, isolated): | maximum rated current: 0.2 A (resettable fuse), maximum peak switched voltage: 30 V DC | ||
Further Information
| power consumption, 18 dBu mode: | 4.8 W | ||
| power consumption, 24 dBu mode: | 6.8 W | ||
| sample frequency: | 48 kHz or 44.1 kHz (automatically synchronised to the configured device system sample frequency) | ||
| connector style: | audio input: XLR-3 female audio output: XLR-3 male GPIO: SubD-9 female |
||
Note
All values are typical values.
52-7230A/52-7235A - XC Mic/Headphone/GPIO Module, 4 ch.
General Information
- 4 mic/line inputs with remote preamp, XLR3 female, 18dBu max., 48V phantom
- 4 stereo headphone outputs, Neutrik Combicon connectors
- 4 general purpose inputs, isolated
- 8 general purpose outputs, isolated
- 4 analog control inputs, 4 DSub-9
A/D Converter
| input sensitivity: | -77 dBu (at 0 dBFS = 18 dBu, max. analog gain= +63 dB, max. digital gain = +20 dB, reference level = +6 dBu) | ||
| maximum input level: | +18 dBu | ||
| gain setting: | analog gain: 0 dB, 8 dB … 63 dB in 1 dB-steps, digital gain -20 dB … +20 dB in 1 dB-steps | ||
| frequency response: | < 0.03 dB | ||
| input impedance: | 5 kOhm | ||
| dynamic range: | > 111 dB (A-weighted) | ||
| signal to noise ratio: | > 109 dB (unweighted) | ||
| THD+N: | < -87 dB / 0.004% (-1 dBFS, +17 dBu, 0 dB analog / digital gain) | ||
| equivalent input noise: | < -127 dBu (150 Ohm source), < -126 dBu (200 Ohm source) | ||
| crosstalk: | < -110 dB (1 kHz) | ||
| phantom power 48V: | switchable per input channel, unloaded input: 48V +/- 10% | ||
| max. input level: | 18 dBu (balanced) | ||
| common mode rejection: | > 60 dB | ||
| converter technology: | 24 bit, oversampling sigma-delta | ||
D/A Converter
| max. output level (headphones, single ended): | 18 dBu | ||
| output impedance: | 100 Ohm | ||
| load impedance (outputs short circuit protected): | > 32 Ohm | ||
| frequency response: | < 0.1 dB | ||
| THD+N: | < -82 dB / 0.008% (-1 dBFS, 100 Ohm load) | ||
| crosstalk: | < -80 dB (unbalanced) | ||
| dynamic range: | > 104 dB (A-weighted) | ||
| signal to noise ratio: | > 102 dB (unweighted) | ||
| DC offset voltage: | < 10 mV | ||
| converter technology: | 24 bit, oversampling sigma-delta | ||
General Purpose Inputs / Outputs (GPI/GPO)
| 4 not isolated analog control inputs to connect external potentiometers for level controlling: | Do not use any of the ACI signals for other purposes than wiring to the potentiometer! ACI_VLO must not be connected to chassis, housing, earth, shield or other common signals! The potentiometer must have a resistance value of 10 kOhms (linear) |
||
| 4 GPIs (optocoupler, isolated): | external ON voltage 5 V … 24 V (DC) without external resistor, internal current limiter to 4 mA current for ON, OFF voltage: 0 V … + 1.5 V | ||
| 8 GPOs (electronic relay, isolated): | maximum rated current: 0.2 A (resettable fuse), maximum peak switched voltage: 30 V DC | ||
Further Information
| power consumption: | 11.6 W | ||
| sample frequency: | 48 kHz or 44.1 kHz (automatically synchronised to the configured device system sample frequency) | ||
| connector style: | audio input: XLR-3 female audio output: combined XLR-3 female/ 1/4“ TRS jack GPIO: SubD-9 female |
||
Note
All values are typical values.
Warning
The wiring of microphone inputs of DHD microphone input modules is not designed to support operation with parallel external phantom power. Using it might result in damages of the pre-amplifier or phantom power generator.
52-7255A/52-7258A - XC Mic/Line Module, 8 ch., iso.
General Information
- 8 mic/line inputs with remote preamp, 0…65 dB, 26 dBu max. input level
- isolated input stages
- phantom power 48V indiv. switchable
- 4 general purpose inputs, isolated
- 4 general purpose outputs, isolated
A/D Converter
| input sensitivity: | -79 dBu (at Toolbox settings: “Headroom 20dB”, “Level Adjust 6dBu = -20dBFS = 0dBint”, maximum analog gain +70 dB) | ||
| maximum input level: | +26 dBu | ||
| analog gain setting: | -20 dB…+70 dB in 1 dB steps
Note |
||
| frequency response: | < 0.03 dB | ||
| input impedance: | 5 kOhm | ||
| dynamic range: | > 112 dB (A-weighted) | ||
| signal to noise ratio: | > 110 dB (unweighted) | ||
| THD+N: | < -85 dB / 0.006% (-1 dBFS, +14 dBu) | ||
| equivalent input noise: | < -127 dBu (150 Ohm source), < -126 dBu (200 Ohm source) | ||
| crosstalk: | < -120 dB (1 kHz) | ||
| phantom power 48V: | switchable per input channel, unloaded input: 48V +/- 10% | ||
| common mode rejection: | > 60 dB | ||
| converter technology: | 24 bit, oversampling sigma-delta | ||
General Purpose Inputs / Outputs (GPI/GPO)
| 4 GPIs (optocoupler, isolated): | external ON voltage 5 V … 24 V (DC) without external resistor, internal current limiter to 4 mA current for ON, OFF voltage: 0 V … + 1.5 V | ||
| 4 GPOs (electronic relay, isolated): | maximum rated current: 0.2 A (resettable fuse), maximum peak switched voltage: 30 V DC | ||
Further Information
| power consumption: | 11.7 W | ||
| sample frequency: | 48 kHz or 44.1 kHz (automatically synchronised to the configured device system sample frequency) | ||
| connector style: | audio input: XLR-3 female GPIO: SubD-9 female |
||
Note
All values are typical values.
Warning
The wiring of microphone inputs of DHD microphone input modules is not designed to support operation with parallel external phantom power. Using it might result in damages of the pre-amplifier or phantom power generator.
52-1330B - XS Multi-I/O Box
General Information
2 Mic/Line inputs, preamp, 48V 2 stereo headphone outputs 8 analog line inputs, el. bal., 24dBu 8 analog line outputs, el. bal., 24dBu 3 AES3/EBU inputs, 1 SPDIF input 2 AES3/EBU outputs, 1 SPDIF output 2 USB Audio IF, 10 GPI, 10 GPO,2 ACI
Mic/Line - A/D Converter
| input sensitivity: | -77 dBu (at 0 dBFS = 18 dBu, max. analog gain= +63 dB, max. digital gain = +20 dB, reference level = +6 dBu) | ||
| maximum input level: | +18 dBu | ||
| gain setting: | analog gain: 0 dB, 10 dB … 63 dB in 1 dB-steps, digital gain -20 dB … +20 dB in 1 dB-steps | ||
| frequency response: | < 0.03 dB | ||
| input impedance: | 5 kOhm | ||
| dynamic range: | > 111 dB (A-weighted) | ||
| signal to noise ratio: | > 109 dB (unweighted) | ||
| THD+N: | < -82 dB / 0.008% (-1 dBFS, +17 dBu, 0 dB analog / digital gain) | ||
| equivalent input noise: | < -127 dBu (150 Ohm source), < -126 dBu (200 Ohm source) | ||
| crosstalk: | < -110 dB (1 kHz) | ||
| phantom power 48V: | switchable per input channel, unloaded input: 48V +/- 10% | ||
| max. input level: | 18 dBu (balanced) | ||
| common mode rejection: | > 45 dB | ||
| converter technology: | 24 bit, oversampling sigma-delta | ||
Headphones - D/A Converter
| max. output level (single ended): | 18 dBu | ||
| output impedance: | 100 Ohm | ||
| load impedance (outputs short circuit protected): | > 32 Ohm | ||
| frequency response: | < 0.1 dB | ||
| THD+N: | < -84 dB / 0.006% (-1 dBFS, 100 Ohm load) | ||
| crosstalk: | < -80 dB (unbalanced) | ||
| dynamic range: | > 107 dB (A-weighted) | ||
| signal to noise ratio: | > 105 dB (unweighted) | ||
| DC offset voltage: | < 10 mV | ||
| converter technology: | 24 bit, oversampling sigma-delta | ||
Line - A/D Converter
| max. input level: | 24 dBu (balanced) | ||
| input impedance: | 15 kOhm | ||
| frequency response: | < 0.05 dB | ||
| THD+N: | < -85 dB / 0.006% (-1 dBFS, +23 dBu) | ||
| crosstalk: | < -100 dB | ||
| dynamic range: | > 98 dB (A-weighted) | ||
| common mode rejection: | > 40 dB | ||
| converter technology: | 24 bit, oversampling sigma-delta | ||
Line - D/A Converter
| max. output level: | 24 dBu (balanced) | ||
| output impedance: | 25 Ohm | ||
| minimum load (outputs short circuit protected): | 600 Ohm | ||
| frequency response: | < 0.1 dB | ||
| THD+N: | < -84 dB / 0.006% (-1 dBFS, +23 dBu) | ||
| crosstalk: | < -90 dB | ||
| dynamic range: | > 104 dB (A-weighted) | ||
| signal to noise ratio: | > 102 dB (unweighted) | ||
| DC offset voltage: | < 10 mV | ||
| common mode rejection (output impedance): | > 60 dB | ||
| common mode rejection (output voltage): | > 40 dB | ||
| converter technology: | 24 bit, oversampling sigma-delta | ||
Digital Inputs
| input impedance: | 110 Ohm (AES3/EBU) or 75 Ohm (S/PDIF) | ||
| input sensitivity: | > 200mV | ||
| input sample rate converters (SRC): | yes, with bypass mode (switchable by configuration software) | ||
| SRC input sampling frequency range: | 28 kHz … 195 kHz | ||
| frequency response: | < 0.01 dB | ||
| dynamic range (SRC off): | > 144 dB (unweighted) | ||
| signal to noise ratio (SRC off): | > 144 dB (unweighted) | ||
| THD+N (SRC on, 44.1 kHz to 48 kHz): | < -130 dB / 0.00003% (-1 dBFS test signal) | ||
| max. input jitter: | > 40 ns (at 48 kHz), > 0.25 UI | ||
Digital Outputs
| output impedance (AES3/EBU): | 110 Ohm | ||
| output impendance (S/PDIF): | 75 Ohm | ||
| output level (AES3/EBU): | 3.4 V (into 110 Ohm load) | ||
| output level (S/PDIF): | 0.5 V (into 75 Ohm load) | ||
| dynamic range (24 bit, dither off): | > 144 dB (unweighted) | ||
| signal to noise ratio (SRC off): | > 144 dB (unweighted) | ||
| THD+N (SRC on, 44.1 kHz to 48 kHz): | < -130 dB / 0.00003% (-1 dBFS test signal) | ||
| dither: | off, 16, 20 bit (switchable by configuration software) | ||
| jitter: | < 2 ns (peak) | ||
USB audio port
- 1 stereo input, sample rate converter, 16 bit
- 1 stereo output, sample rate converter (linked to associated input if activated in Toolbox), 16 bit
- USB full-speed transceivers
- compliant with USB 2.0 specification
- bus-powered USB circuit (the Windows or Mac driver still works when 52-1330 is powered off)
- default Windows or Mac USB audio device driver is used, no additional driver required
General Purpose Inputs / Outputs (GPI/GPO)
| 2 not isolated analog control inputs to connect external potentiometers for level controlling: | Do not use any of the ACI signals for other purposes than wiring to the potentiometer! ACI_VLO must not be connected to chassis, housing, earth, shield or other common signals! The potentiometer must have a resistance value of 10 kOhms (linear) |
||
| 10 GPIs (optocoupler, isolated): | external ON voltage 5 V … 24 V (DC) without external resistor, internal current limiter to 4 mA current for ON, OFF voltage: 0 V … + 1.5 V | ||
| 10 GPOs (electronic relay, isolated): | maximum rated current: 0.2 A (resettable fuse), maximum peak switched voltage: 30 V DC | ||
Further Information
| power consumption: | 11 W | ||
| sample frequency: | 48 kHz or 44.1 kHz (automatically synchronised to the configured device system sample frequency) | ||
| connector style: | audio input: SubD-15 female audio output: SubD-15 female S/PDIF input: RCA connector, female S/PDIF output: RCA connector, female GPIO: SubD-15 female |
||
Note
All values are typical values.
Warning
The wiring of microphone inputs of DHD microphone input modules is not designed to support operation with parallel external phantom power. Using it might result in damages of the pre-amplifier or phantom power generator.
52-1335A - XS Multi-I/O Box
General Information
- 2 Mic/Line inputs, preamp, 48V
- 2 stereo headphone outputs
- 8 analog line inputs, el. bal., 24dBu
- 8 analog line outputs, el. bal., 24dBu
- 3 AES3/EBU inputs, 1 SPDIF input
- 2 AES3/EBU outputs, 1 SPDIF output
- 2 USB Audio IF, 10 GPI, 10 GPO,2 ACI
Mic/Line - A/D Converter
| input sensitivity: | -77 dBu (at 0 dBFS = 18 dBu, max. analog gain= +63 dB, max. digital gain = +20 dB, reference level = +6 dBu) | ||
| maximum input level: | +18 dBu | ||
| gain setting: | analog gain: 0 dB, 10 dB … 63 dB in 1 dB-steps, digital gain -20 dB … +20 dB in 1 dB-steps | ||
| frequency response: | < 0.03 dB | ||
| input impedance: | 5 kOhm | ||
| dynamic range: | > 111 dB (A-weighted) | ||
| signal to noise ratio: | > 109 dB (unweighted) | ||
| THD+N: | < -82 dB / 0.008% (-1 dBFS, +17 dBu, 0 dB analog / digital gain) | ||
| equivalent input noise: | < -127 dBu (150 Ohm source), < -126 dBu (200 Ohm source) | ||
| crosstalk: | < -110 dB (1 kHz) | ||
| phantom power 48V: | switchable per input channel, unloaded input: 48V +/- 10% | ||
| max. input level: | 18 dBu (balanced) | ||
| common mode rejection: | > 45 dB | ||
| converter technology: | 24 bit, oversampling sigma-delta | ||
Headphone - D/A Converter
| max. output level (single ended): | 18 dBu | ||
| output impedance: | 100 Ohm | ||
| load impedance (outputs short circuit protected): | > 32 Ohm | ||
| frequency response: | < 0.1 dB | ||
| THD+N: | < -84 dB / 0.006% (-1 dBFS, 100 Ohm load) | ||
| crosstalk: | < -80 dB (unbalanced) | ||
| dynamic range: | > 107 dB (A-weighted) | ||
| signal to noise ratio: | > 105 dB (unweighted) | ||
| DC offset voltage: | < 10 mV | ||
| converter technology: | 24 bit, oversampling sigma-delta | ||
Line - A/D Converter
| max. input level: | 24 dBu (balanced) | ||
| input impedance: | 15 kOhm | ||
| frequency response: | < 0.05 dB | ||
| THD+N: | < -85 dB / 0.006% (-1 dBFS, +23 dBu) | ||
| crosstalk: | < -100 dB | ||
| dynamic range: | > 98 dB (A-weighted) | ||
| common mode rejection: | > 40 dB | ||
| converter technology: | 24 bit, oversampling sigma-delta | ||
Line - D/A Converter
| max. output level: | 24 dBu (balanced) | ||
| output impedance: | 25 Ohm | ||
| minimum load (outputs short circuit protected): | 600 Ohm | ||
| frequency response: | < 0.1 dB | ||
| THD+N: | < -84 dB / 0.006% (-1 dBFS, +23 dBu) | ||
| crosstalk: | < -90 dB | ||
| dynamic range: | > 104 dB (A-weighted) | ||
| signal to noise ratio: | > 102 dB (unweighted) | ||
| DC offset voltage: | < 10 mV | ||
| common mode rejection (output impedance): | > 60 dB | ||
| common mode rejection (output voltage): | > 40 dB | ||
| converter technology: | 24 bit, oversampling sigma-delta | ||
Digital Inputs
| input impedance: | 110 Ohm (AES3/EBU) or 75 Ohm (S/PDIF) | ||
| input sensitivity: | > 200mV | ||
| input sample rate converters (SRC): | yes, with bypass mode (switchable by configuration software) | ||
| SRC input sampling frequency range: | 28 kHz … 108 kHz | ||
| frequency response: | < 0.01 dB | ||
| dynamic range (SRC off): | > 144 dB (unweighted) | ||
| signal to noise ratio (SRC off): | > 144 dB (unweighted) | ||
| THD+N (SRC on, 44.1 kHz to 48 kHz): | < -130 dB / 0.00003% (-1 dBFS test signal) | ||
| max. input jitter: | > 40 ns (at 48 kHz), > 0.25 UI | ||
Digital Outputs
| output impedance (AES3/EBU): | 110 Ohm | ||
| output impendance (S/PDIF): | 75 Ohm | ||
| output level (AES3/EBU): | 3.4 V (into 110 Ohm load) | ||
| output level (S/PDIF): | 0.5 V (into 75 Ohm load) | ||
| output sample rate converters (SRC): | yes (slaved to related input), with bypass mode (switchable by configuration software) | ||
| SRC output sampling frequency range: | 28 kHz … 54 kHz | ||
| dynamic range (24 bit, dither off): | > 144 dB (unweighted) | ||
| signal to noise ratio (SRC off): | > 144 dB (unweighted) | ||
| THD+N (SRC on, 44.1 kHz to 48 kHz): | < -130 dB / 0.00003% (-1 dBFS test signal) | ||
| dither: | off, 16, 20 bit (switchable by configuration software) | ||
| jitter: | < 2 ns (peak) | ||
USB audio port
- 1 stereo input, sample rate converter, 16 bit
- 1 stereo output, sample rate converter (linked to associated input if activated in Toolbox), 16 bit
- USB full-speed transceivers
- compliant with USB 2.0 specification
- bus-powered USB circuit (the Windows or Mac driver still works when 52-1335 is powered off)
- default Windows or Mac USB audio device driver is used, no additional driver required
General Purpose Inputs / Outputs (GPI/GPO)
| 2 not isolated analog control inputs to connect external potentiometers for level controlling: | Do not use any of the ACI signals for other purposes than wiring to the potentiometer! ACI_VLO must not be connected to chassis, housing, earth, shield or other common signals! The potentiometer must have a resistance value of 10 kOhms (linear) |
||
| 10 GPIs (optocoupler, isolated): | external ON voltage 5 V … 24 V (DC) without external resistor, internal current limiter to 4 mA current for ON, OFF voltage: 0 V … + 1.5 V | ||
| 10 GPOs (electronic relay, isolated): | maximum rated current: 0.2 A (resettable fuse), maximum peak switched voltage: 30 V DC | ||
Further Information
| power consumption: | 11 W | ||
| sample frequency: | 48 kHz or 44.1 kHz (automatically synchronised to the configured device system sample frequency) | ||
| connector style: | audio input: SubD-15 female audio output: SubD-15 female S/PDIF input: RCA connector, female S/PDIF output: RCA connector, female GPIO: SubD-15 female |
||
Note
All values are typical values.
Warning
The wiring of microphone inputs of DHD microphone input modules is not designed to support operation with parallel external phantom power. Using it might result in damages of the pre-amplifier or phantom power generator.
52-1340A - Multi I/O Box II
General Information
- 2 Mic/Line inputs, preamp, 48V
- 2 stereo headphone outputs
- 4 analog line inputs, el. bal., 24dBu
- 4 analog line outputs, el. bal., 24dBu
- 4 AES3/EBU inputs
- 4 AES3/EBU outputs
- 1 USB Audio Interface
- 8 GPI (4 of them can be used as ACI)
- 8 GPO (2 of them are powered GPO for m!ka Mic Arm On Air LED)
Mic/Line - A/D Converter
| input sensitivity: | | -98 dBu (at 0 dBFS = 24 dBu, max. analog gain= +84 dB, max. digital gain = +20 dB, reference level = +6 dBu) | |
| maximum input level: | | +24 dBu | |
| gain setting: | analog gain: -9 dB … 75 dB in 1 dB-steps, digital gain -20 dB … +20 dB in 1 dB-steps | ||
| frequency response: | < 0.03 dB | ||
| input impedance: | 5 kOhm | ||
| dynamic range: | | > 110 dB (A-weighted) | |
| signal to noise ratio: | | > 108 dB (unweighted) | |
| THD+N: | | < -90 dB / 0.003% (-1 dBFS, +23 dBu, 0 dB analog / digital gain) | |
| equivalent input noise: | < -127 dBu (150 Ohm source), < -126 dBu (200 Ohm source) | ||
| crosstalk: | < -110 dB (1 kHz) | ||
| phantom power 48V: | switchable per input channel, unloaded input: 48V +/- 10% | ||
| max. input level: | 24 dBu (balanced) | ||
| common mode rejection: | | > 58 dB | |
| converter technology: | 24 bit, oversampling sigma-delta | ||
Headphones - D/A Converter
| max. output level (single ended): | 15 dBu | ||
| output impedance: | <3 Ohm | ||
| load impedance (outputs short circuit protected): | > 32 Ohm | ||
| frequency response: | < 0.1 dB | ||
| THD+N: | < -88 dB / 0.004% (-1 dBFS, 100 Ohm load) | ||
| crosstalk: | < -80 dB (unbalanced) | ||
| dynamic range: | > 106 dB (A-weighted) | ||
| signal to noise ratio: | > 104 dB (unweighted) | ||
| DC offset voltage: | < 10 mV | ||
| converter technology: | 24 bit, oversampling sigma-delta | ||
Line - A/D Converter
| max. input level: | 24 dBu (balanced) | ||
| input impedance: | 10 kOhm | ||
| frequency response: | < 0.05 dB | ||
| THD+N: | < -85 dB / 0.006% (-1 dBFS, +23 dBu) | ||
| crosstalk: | < -100 dB | ||
| dynamic range: | > 99 dB (A-weighted) | ||
| signal-to-noise: | > 97 dB (unweighted) | ||
| common mode rejection: | > 40 dB | ||
| converter technology: | 24 bit, oversampling sigma-delta | ||
Line - D/A Converter
| max. output level: | 24 dBu (balanced) | ||
| output impedance: | 25 Ohm | ||
| minimum load (outputs short circuit protected): | 600 Ohm | ||
| frequency response: | < 0.1 dB | ||
| THD+N: | < -88 dB / 0.004% (-1 dBFS, +23 dBu) | ||
| crosstalk: | < -90 dB | ||
| dynamic range: | > 106 dB (A-weighted) | ||
| signal to noise ratio: | > 104 dB (unweighted) | ||
| DC offset voltage: | < 10 mV | ||
| common mode rejection (output impedance): | > 60 dB | ||
| common mode rejection (output voltage): | > 40 dB | ||
| converter technology: | 24 bit, oversampling sigma-delta | ||
Digital Inputs
| input impedance: | 110 Ohm (AES3/EBU) or 75 Ohm (S/PDIF) | ||
| input sensitivity: | > 200mV | ||
| input sample rate converters (SRC): | yes, with bypass mode (switchable by configuration software) | ||
| SRC input sampling frequency range: | 28 kHz … 54 kHz | ||
| frequency response: | < 0.01 dB | ||
| dynamic range (SRC off): | > 144 dB (unweighted) | ||
| signal to noise ratio (SRC off): | > 144 dB (unweighted) | ||
| THD+N (SRC on, 44.1 kHz to 48 kHz): | < -130 dB / 0.00003% (-1 dBFS test signal) | ||
| max. input jitter: | > 40 ns (at 48 kHz), > 0.25 UI | ||
| supported standards: | AES3/EBU or S/PDIF (switchable by configuration software) | ||
Digital Outputs
| output impedance: | 110 Ohm (AES/EBU) or 75 Ohm (S/PDIF) | ||
| output impendance (S/PDIF): | 75 Ohm | ||
| output level (AES3/EBU): | 3.4 V (into 110 Ohm load) | ||
| output level (S/PDIF): | 0.5 V (into 75 Ohm load) | ||
| output sample rate converters (SRC): | yes (following the related input), with bypass mode (switchable by configuration software) | ||
| SRC output sampling frequency range: | 28 kHz … 54 kHz | ||
| dynamic range (24 bit, dither off): | > 144 dB (unweighted) | ||
| signal to noise ratio (SRC off): | > 144 dB (unweighted) | ||
| THD+N (SRC on, 44.1 kHz to 48 kHz): | < -130 dB / 0.00003% (-1 dBFS test signal) | ||
| dither: | off, 16, 20 bit (switchable by configuration software) | ||
| jitter: | < 2 ns (peak) | ||
| supported standards: | AES3/EBU or S/PDIF (switchable by configuration software) | ||
USB audio port
- USB-C connector
- 1 stereo input, sample rate converter, 16 bit
- 1 stereo output, sample rate converter (linked to associated input if activated in Toolbox), 16 bit
- USB full-speed transceivers
- compliant with USB 2.0 specification
- bus-powered USB circuit (the Windows or Mac driver still works when 52-1340 is powered off)
- default Windows or Mac USB audio device driver is used, no additional driver required
General Purpose Inputs / Outputs (GPI/GPO)
8 GPI (4 of them can be used as ACI)
8 GPO (2 of them are powered GPO for m!ka Mic Arm On Air LED)
Further Information
| power consumption: | 12.2 W | ||
| sample frequency: | 48 kHz or 44.1 kHz (automatically synchronised to the configured device system sample frequency) | ||
| connector style: | mic input: XLR-3 female other audio input: SubD-15 female audio output: SubD-15 female GPIO: SubD-15 female USB audio: USB-C |
||
Note
All values are typical values.
Warning
The wiring of microphone inputs of DHD microphone input modules is not designed to support operation with parallel external phantom power. Using it might result in damages of the pre-amplifier or phantom power generator.
52-1830A/B/C - XS2 I/O Core
General Information
- 2 Mic/Line inputs, preamp, 48V
- 1 stereo headphone output
- 2 analog line inputs, el. bal., 24dBu
- 2 analog line inputs, unbal.
- 4 analog line outputs, el. bal., 24dBu
- 2 analog line outputs, unbal.
- 3 AES3/EBU inputs,
- 3 AES3/EBU outputs,
- 1 SPDIF or ADAT input
- 1 SPDIF or ADAT output
- 1 USB Audio IF, 2 GPI, 4 GPO
Mic/Line - A/D Converter
| input sensitivity: | -77 dBu (at 0 dBFS = 18 dBu, max. analog gain= +63 dB, max. digital gain = +20 dB, reference level = +6 dBu) | ||
| maximum input level: | +18 dBu | ||
| gain setting: | analog gain: 0 dB, 10 dB … 63 dB in 1 dB-steps, digital gain -20 dB … +20 dB in 1 dB-steps | ||
| frequency response: | < 0.03 dB | ||
| input impedance: | 5 kOhm | ||
| dynamic range: | > 111 dB (A-weighted) | ||
| signal to noise ratio: | > 109 dB (unweighted) | ||
| THD+N: | < -82 dB / 0.008% (-1 dBFS, +17 dBu, 0 dB analog / digital gain) | ||
| equivalent input noise: | < -127 dBu (150 Ohm source), < -126 dBu (200 Ohm source) | ||
| crosstalk: | < -110 dB (1 kHz) | ||
| phantom power 48V: | switchable per input channel, unloaded input: 48V +/- 10% | ||
| max. input level: | 18 dBu (balanced) | ||
| common mode rejection: | > 45 dB | ||
| converter technology: | 24 bit, oversampling sigma-delta | ||
Headphones - D/A Converter
| max. output level (single ended): | 18 dBu | ||
| output impedance: | 100 Ohm | ||
| load impedance (outputs short circuit protected): | > 32 Ohm | ||
| frequency response: | < 0.1 dB | ||
| THD+N: | < -84 dB / 0.006% (-1 dBFS, 100 Ohm load) | ||
| crosstalk: | < -80 dB (unbalanced) | ||
| dynamic range: | > 107 dB (A-weighted) | ||
| signal to noise ratio: | > 105 dB (unweighted) | ||
| DC offset voltage: | < 10 mV | ||
| converter technology: | 24 bit, oversampling sigma-delta | ||
Line, balanced - A/D Converter
| max. input level: | 24 dBu (balanced) | ||
| input impedance: | 15 kOhm | ||
| frequency response: | < 0.05 dB | ||
| THD+N: | < -85 dB / 0.006% (-1 dBFS, +23 dBu) | ||
| crosstalk: | < -100 dB | ||
| dynamic range: | > 98 dB (A-weighted) | ||
| common mode rejection: | > 40 dB | ||
| converter technology: | 24 bit, oversampling sigma-delta | ||
Line, un-balanced - A/D Converter
| max. input level: | 13 dBu (un-balanced) | ||
| input impedance: | > 40 kOhm | ||
| frequency response: | < 0.05 dB | ||
| THD+N: | < -85 dB / 0.006% (-1 dBFS, +12 dBu) | ||
| crosstalk: | < -80 dB | ||
| dynamic range: | > 98 dB (A-weighted) | ||
| converter technology: | 24 bit, oversampling sigma-delta | ||
Line, balanced - D/A Converter
| max. output level: | 24 dBu (balanced) | ||
| output impedance: | 25 Ohm | ||
| minimum load (outputs short circuit protected): | 600 Ohm | ||
| frequency response: | < 0.1 dB | ||
| THD+N: | < -84 dB / 0.006% (-1 dBFS, +23 dBu) | ||
| crosstalk: | < -90 dB | ||
| dynamic range: | > 104 dB (A-weighted) | ||
| signal to noise ratio: | > 102 dB (unweighted) | ||
| DC offset voltage: | < 10 mV | ||
| common mode rejection (output impedance): | > 60 dB | ||
| common mode rejection (output voltage): | > 40 dB | ||
| converter technology: | 24 bit, oversampling sigma-delta | ||
Line, un-balanced - D/A Converter
| max. output level: | 8 dBu (balanced) | ||
| output impedance: | ca. 250 Ohm | ||
| frequency response: | < 0.1 dB | ||
| THD+N: | < -84 dB / 0.006% (-1 dBFS, +7 dBu) | ||
| crosstalk: | < -80 dB | ||
| dynamic range: | > 104 dB (A-weighted) | ||
| signal to noise ratio: | > 102 dB (unweighted) | ||
| DC offset voltage: | < 10 mV | ||
| converter technology: | 24 bit, oversampling sigma-delta | ||
Digital Inputs
| input impedance: | 110 Ohm (AES3/EBU) | ||
| input sensitivity: | > 200mV | ||
| input sample rate converters (SRC): | yes, with bypass mode (switchable by configuration software) | ||
| SRC input sampling frequency range: | 28 kHz … 108 kHz | ||
| frequency response: | < 0.01 dB | ||
| dynamic range (SRC off): | > 144 dB (unweighted) | ||
| signal to noise ratio (SRC off): | > 144 dB (unweighted) | ||
| THD+N (SRC on, 44.1 kHz to 48 kHz): | < -130 dB / 0.00003% (-1 dBFS test signal) | ||
| max. input jitter: | > 40 ns (at 48 kHz), > 0.25 UI | ||
Digital Outputs
| output impedance (AES3/EBU): | 110 Ohm | ||
| output level (AES3/EBU): | 3.4 V (into 110 Ohm load) | ||
| output sample rate converters (SRC): | yes (slaved to related input), with bypass mode (switchable by configuration software) | ||
| SRC output sampling frequency range: | 28 kHz … 54 kHz | ||
| dynamic range (24 bit, dither off): | > 144 dB (unweighted) | ||
| signal to noise ratio (SRC off): | > 144 dB (unweighted) | ||
| THD+N (SRC on, 44.1 kHz to 48 kHz): | < -130 dB / 0.00003% (-1 dBFS test signal) | ||
| dither: | off, 16, 20 bit (switchable by configuration software) | ||
| jitter: | < 2 ns (peak) | ||
USB audio port
- 1 stereo input, sample rate converter
- 1 stereo output, sample rate converter (linked to associated input if activated in Toolbox)
- full-speed transceivers
- compliant with USB 2.0 specification
- elf-powered USB circuit
- default Windows or Mac USB audio device driver is used, no additional driver required
- iOS devices with version 7.0 or higher can be connected via a camera connection kit for playback and recording
General Purpose Inputs / Outputs (GPI/GPO)
| 2 GPIs (optocoupler, isolated): | external ON voltage 5 V … 24 V (DC) without external resistor, internal current limiter to 4 mA current for ON, OFF voltage: 0 V … + 1.5 V | ||
| 4 GPOs (electronic relay, isolated): | maximum rated current: 0.2 A (resettable fuse), maximum peak switched voltage: 30 V DC | ||
Further Information
| power consumption: | 30 W | ||
| sample frequency: | 48 kHz or 44.1 kHz (automatically synchronised to the configured device system sample frequency) | ||
| connector style: | Line and Mic inputs, balanced: XLR-3 female Line outputs 1 and 2, balanced: XLR-3 male Line inputs, un-balanced: RCA connector Line outputs, un-balanced: RCA connector Line outputs 5 and 6,balanced: SubD-15 female Headphones: combined XLR-3 female/ 1/4” TRS jack and same signal output on SubD-15 female AES3 input 1: XLR-3 female AES3 output 1: XLR-3 male AES3 input 2 and 3: SubD-15 female AES3 output 2 and 3: SubD-15 female GPIO: SubD-9 female S/PDIF / ADAT input: TOSLINK, optical S/PDIF / ADAT output: TOSLINK, optical GPIO: SubD-15 female | ||
Note
All values are typical values.
Warning
The wiring of microphone inputs of DHD microphone input modules is not designed to support operation with parallel external phantom power. Using it might result in damages of the pre-amplifier or phantom power generator.
52-1156A/B/C/D/E - TX Multitouch Mixer
General Information
- 1 Mic/Line inputs, preamp, 48V
- 1 stereo headphone outputs
Mic/Line - A/D Converter
| input sensitivity: | -77 dBu (at 0 dBFS = 18 dBu, max. analog gain= +63 dB, max. digital gain = +20 dB, reference level = +6 dBu) | ||
| maximum input level: | +18 dBu | ||
| gain setting: | analog gain: 0 dB, 10 dB … 63 dB in 1 dB-steps, digital gain -20 dB … +20 dB in 1 dB-steps | ||
| frequency response: | < 0.03 dB | ||
| input impedance: | 5 kOhm | ||
| dynamic range: | > 111 dB (A-weighted) | ||
| signal to noise ratio: | > 109 dB (unweighted) | ||
| THD+N: | < -82 dB / 0.008% (-1 dBFS, +17 dBu, 0 dB analog / digital gain) | ||
| equivalent input noise: | < -127 dBu (150 Ohm source), < -126 dBu (200 Ohm source) | ||
| crosstalk: | < -110 dB (1 kHz) | ||
| phantom power 48V: | switchable per input channel, unloaded input: 48V +/- 10% | ||
| max. input level: | 18 dBu (balanced) | ||
| common mode rejection: | > 45 dB | ||
| converter technology: | 24 bit, oversampling sigma-delta | ||
Headphones - D/A Converter
| max. output level (single ended): | 18 dBu | ||
| output impedance: | 100 Ohm | ||
| load impedance (outputs short circuit protected): | > 32 Ohm | ||
| frequency response: | < 0.1 dB | ||
| THD+N: | < -84 dB / 0.006% (-1 dBFS, 100 Ohm load) | ||
| crosstalk: | < -80 dB (unbalanced) | ||
| dynamic range: | > 107 dB (A-weighted) | ||
| signal to noise ratio: | > 105 dB (unweighted) | ||
| DC offset voltage: | < 10 mV | ||
| converter technology: | 24 bit, oversampling sigma-delta | ||
Further Information
| power consumption: | 15 W | ||
| sample frequency: | 48 kHz or 44.1 kHz (automatically synchronised to the configured device system sample frequency) | ||
| connector style: | audio input: XLR-3 female audio output: combined XLR-3 female/ 1/4“ TRS jack |
||
Note
All values are typical values.
Warning
The wiring of microphone inputs of DHD microphone input modules is not designed to support operation with parallel external phantom power. Using it might result in damages of the pre-amplifier or phantom power generator.
52-5614A/B/C/M/N - SX2 Central & Fader Module
General Information
- 1 Mic/Line inputs, preamp, 48V
- 1 stereo headphones output
- 2 analog line outputs, 18dBu max., XLR3 male, el. balanced, 24 bit
- 2 general purpose intputs, isolated
- 2 general purpose outputs, isolated
- 1 DSub-9 connectors for GPIOs
Mic/Line - A/D Converter
| input sensitivity: | -77 dBu (at 0 dBFS = 18 dBu, max. analog gain= +63 dB, max. digital gain = +20 dB, reference level = +6 dBu) | ||
| maximum input level: | +18 dBu | ||
| gain setting: | analog gain: 0 dB, 10 dB … 63 dB in 1 dB-steps, digital gain -20 dB … +20 dB in 1 dB-steps | ||
| frequency response: | < 0.03 dB | ||
| input impedance: | 5 kOhm | ||
| dynamic range: | > 111 dB (A-weighted) | ||
| signal to noise ratio: | > 109 dB (unweighted) | ||
| THD+N: | < -82 dB / 0.008% (-1 dBFS, +17 dBu, 0 dB analog / digital gain) | ||
| equivalent input noise: | < -127 dBu (150 Ohm source), < -126 dBu (200 Ohm source) | ||
| crosstalk: | < -110 dB (1 kHz) | ||
| phantom power 48V: | switchable per input channel, unloaded input: 48V +/- 10% | ||
| max. input level: | 18 dBu (balanced) | ||
| common mode rejection: | > 45 dB | ||
| converter technology: | 24 bit, oversampling sigma-delta | ||
Headphones - D/A Converter
| max. output level (single ended): | 18 dBu | ||
| output impedance: | 100 Ohm | ||
| load impedance (outputs short circuit protected): | > 32 Ohm | ||
| frequency response: | < 0.1 dB | ||
| THD+N: | < -81 dB / 0.009% (-1 dBFS, 100 Ohm load) | ||
| crosstalk: | < -80 dB (unbalanced) | ||
| dynamic range: | > 104 dB (A-weighted) | ||
| signal to noise ratio: | > 102 dB (unweighted) | ||
| DC offset voltage: | < 10 mV | ||
| converter technology: | 24 bit, oversampling sigma-delta | ||
Line - D/A Converter
| max. output level: | 18 dBu (balanced) |
| output impedance: | 25 Ohm |
| minimum load (outputs short circuit protected): | 600 Ohm |
| frequency response: | < 0.1 dB |
| THD+N: | < -89 dB / 0.0035% (-1 dBFS, +17 dBu) |
| crosstalk: | < -90 dB |
| dynamic range: | > 106 dB (A-weighted) |
| signal to noise ratio: | > 104 dB (unweighted) |
| DC offset voltage: | < 10 mV |
| common mode rejection (output impedance): | > 60 dB |
| common mode rejection (output voltage): | > 40 dB |
| converter technology: | 24 bit, oversampling sigma-delta |
Further Information
| power consumption: | 25 W | ||
| sample frequency: | 48 kHz or 44.1 kHz (automatically synchronised to the configured device system sample frequency) | ||
| connector style: | mic input: XLR-3 female headphones output: combined XLR-3 female/ 1/4” TRS jack analogue line outputs: XLR-3 male GPIO: SubD-9 female |
||
Note
All values are typical values.
Warning
The wiring of microphone inputs of DHD microphone input modules is not designed to support operation with parallel external phantom power. Using it might result in damages of the pre-amplifier or phantom power generator.
52-5810A/M - RX2 Central Module
General Information
- 1 Mic/Line inputs, preamp, 48V
- 1 stereo headphones output
- 2 analog line outputs, 18dBu max., XLR3 male, el. balanced, 24 bit
- 2 general purpose intputs, isolated
- 2 general purpose outputs, isolated
- 1 DSub-9 connectors for GPIOs
Mic/Line - A/D Converter
| input sensitivity: | -77 dBu (at 0 dBFS = 18 dBu, max. analog gain= +63 dB, max. digital gain = +20 dB, reference level = +6 dBu) | ||
| maximum input level: | +18 dBu | ||
| gain setting: | analog gain: 0 dB, 10 dB … 63 dB in 1 dB-steps, digital gain -20 dB … +20 dB in 1 dB-steps | ||
| frequency response: | < 0.03 dB | ||
| input impedance: | 5 kOhm | ||
| dynamic range: | > 111 dB (A-weighted) | ||
| signal to noise ratio: | > 109 dB (unweighted) | ||
| THD+N: | < -82 dB / 0.008% (-1 dBFS, +17 dBu, 0 dB analog / digital gain) | ||
| equivalent input noise: | < -127 dBu (150 Ohm source), < -126 dBu (200 Ohm source) | ||
| crosstalk: | < -110 dB (1 kHz) | ||
| phantom power 48V: | switchable per input channel, unloaded input: 48V +/- 10% | ||
| max. input level: | 18 dBu (balanced) | ||
| common mode rejection: | > 45 dB | ||
| converter technology: | 24 bit, oversampling sigma-delta | ||
Headphones - D/A Converter
| max. output level (single ended): | 18 dBu | ||
| output impedance: | 100 Ohm | ||
| load impedance (outputs short circuit protected): | > 32 Ohm | ||
| frequency response: | < 0.1 dB | ||
| THD+N: | < -81 dB / 0.009% (-1 dBFS, 100 Ohm load) | ||
| crosstalk: | < -80 dB (unbalanced) | ||
| dynamic range: | > 104 dB (A-weighted) | ||
| signal to noise ratio: | > 102 dB (unweighted) | ||
| DC offset voltage: | < 10 mV | ||
| converter technology: | 24 bit, oversampling sigma-delta | ||
Line - D/A Converter
| max. output level: | 18 dBu (balanced) |
| output impedance: | 25 Ohm |
| minimum load (outputs short circuit protected): | 600 Ohm |
| frequency response: | < 0.1 dB |
| THD+N: | < -89 dB / 0.0035% (-1 dBFS, +17 dBu) |
| crosstalk: | < -90 dB |
| dynamic range: | > 106 dB (A-weighted) |
| signal to noise ratio: | > 104 dB (unweighted) |
| DC offset voltage: | < 10 mV |
| common mode rejection (output impedance): | > 60 dB |
| common mode rejection (output voltage): | > 40 dB |
| converter technology: | 24 bit, oversampling sigma-delta |
Further Information
| power consumption: | 25 W | ||
| sample frequency: | 48 kHz or 44.1 kHz (automatically synchronised to the configured device system sample frequency) | ||
| connector style: | mic input: XLR-3 female headphones output: combined XLR-3 female/ 1/4“ TRS jack analogue line outputs: XLR-3 male GPIO: SubD-9 female |
||
Note
All values are typical values.
Warning
The wiring of microphone inputs of DHD microphone input modules is not designed to support operation with parallel external phantom power. Using it might result in damages of the pre-amplifier or phantom power generator.
52-1214A/B - DX2 Central & Fader Module
General Information
- 1 Mic/Line inputs, preamp, 48V
- 1 stereo headphones output
- 2 analog line outputs, 18dBu max., XLR3 male, el. balanced, 24 bit
- CTIA st. in/out
Mic/Line - A/D Converter
| input sensitivity: | | -98 dBu (at 0 dBFS = 24 dBu, max. analog gain= +84 dB, max. digital gain = +20 dB, reference level = +6 dBu) | |
| maximum input level: | | +24 dBu | |
| gain setting: | analog gain: -9 dB … 75 dB in 1 dB-steps, digital gain -20 dB … +20 dB in 1 dB-steps | ||
| frequency response: | < 0.03 dB | ||
| input impedance: | 5 kOhm | ||
| dynamic range: | | > 110 dB (A-weighted) | |
| signal to noise ratio: | | > 108 dB (unweighted) | |
| THD+N: | | < -90 dB / 0.003% (-1 dBFS, +23 dBu, 0 dB analog / digital gain) | |
| equivalent input noise: | < -127 dBu (150 Ohm source), < -126 dBu (200 Ohm source) | ||
| crosstalk: | < -110 dB (1 kHz) | ||
| phantom power 48V: | switchable per input channel, unloaded input: 48V +/- 10% | ||
| max. input level: | 24 dBu (balanced) | ||
| common mode rejection: | | > 58 dB | |
| converter technology: | 24 bit, oversampling sigma-delta | ||
Headphones - D/A Converter
| max. output level (single ended): | 15 dBu | ||
| output impedance: | <3 Ohm | ||
| load impedance (outputs short circuit protected): | > 32 Ohm | ||
| frequency response: | < 0.1 dB | ||
| THD+N: | < -88 dB / 0.004% (-1 dBFS, 100 Ohm load) | ||
| crosstalk: | < -80 dB (unbalanced) | ||
| dynamic range: | > 106 dB (A-weighted) | ||
| signal to noise ratio: | > 104 dB (unweighted) | ||
| DC offset voltage: | < 10 mV | ||
| converter technology: | 24 bit, oversampling sigma-delta | ||
Line - D/A Converter
| max. output level: | 24 dBu (balanced) | ||
| output impedance: | 25 Ohm | ||
| minimum load (outputs short circuit protected): | 600 Ohm | ||
| frequency response: | < 0.1 dB | ||
| THD+N: | < -88 dB / 0.004% (-1 dBFS, +23 dBu) | ||
| crosstalk: | < -90 dB | ||
| dynamic range: | > 106 dB (A-weighted) | ||
| signal to noise ratio: | > 104 dB (unweighted) | ||
| DC offset voltage: | < 10 mV | ||
| common mode rejection (output impedance): | > 60 dB | ||
| common mode rejection (output voltage): | > 40 dB | ||
| converter technology: | 24 bit, oversampling sigma-delta | ||
Further Information
| power consumption: | 25 W | ||
| sample frequency: | 48 kHz or 44.1 kHz (automatically synchronised to the configured device system sample frequency) | ||
| connector style: | mic input: XLR-3 female headphones output: combined XLR-3 female/ 1/4” TRS jack analogue line outputs: XLR-3 male unbal. analoge stereo in/mono out: 4-pin 3.5mm CTIA |
||
Note
All values are typical values.
Warning
The wiring of microphone inputs of DHD microphone input modules is not designed to support operation with parallel external phantom power. Using it might result in damages of the pre-amplifier or phantom power generator.
52-1256A/B - TX2 10.1″ Multitouch Mixer
General Information
- 1 Mic/Line inputs, preamp, 48V
- 1 stereo headphones output
- 2 analog line outputs, 18dBu max., XLR3 male, el. balanced, 24 bit
- CTIA st. in/out
Mic/Line - A/D Converter
| input sensitivity: | | -98 dBu (at 0 dBFS = 24 dBu, max. analog gain= +84 dB, max. digital gain = +20 dB, reference level = +6 dBu) | |
| maximum input level: | | +24 dBu | |
| gain setting: | analog gain: -9 dB … 75 dB in 1 dB-steps, digital gain -20 dB … +20 dB in 1 dB-steps | ||
| frequency response: | < 0.03 dB | ||
| input impedance: | 5 kOhm | ||
| dynamic range: | | > 110 dB (A-weighted) | |
| signal to noise ratio: | | > 108 dB (unweighted) | |
| THD+N: | | < -90 dB / 0.003% (-1 dBFS, +23 dBu, 0 dB analog / digital gain) | |
| equivalent input noise: | < -127 dBu (150 Ohm source), < -126 dBu (200 Ohm source) | ||
| crosstalk: | < -110 dB (1 kHz) | ||
| phantom power 48V: | switchable per input channel, unloaded input: 48V +/- 10% | ||
| max. input level: | 24 dBu (balanced) | ||
| common mode rejection: | | > 58 dB | |
| converter technology: | 24 bit, oversampling sigma-delta | ||
Headphones - D/A Converter
| max. output level (single ended): | 15 dBu | ||
| output impedance: | <3 Ohm | ||
| load impedance (outputs short circuit protected): | > 32 Ohm | ||
| frequency response: | < 0.1 dB | ||
| THD+N: | < -88 dB / 0.004% (-1 dBFS, 100 Ohm load) | ||
| crosstalk: | < -80 dB (unbalanced) | ||
| dynamic range: | > 106 dB (A-weighted) | ||
| signal to noise ratio: | > 104 dB (unweighted) | ||
| DC offset voltage: | < 10 mV | ||
| converter technology: | 24 bit, oversampling sigma-delta | ||
Line - D/A Converter
| max. output level: | 24 dBu (balanced) | ||
| output impedance: | 25 Ohm | ||
| minimum load (outputs short circuit protected): | 600 Ohm | ||
| frequency response: | < 0.1 dB | ||
| THD+N: | < -88 dB / 0.004% (-1 dBFS, +23 dBu) | ||
| crosstalk: | < -90 dB | ||
| dynamic range: | > 106 dB (A-weighted) | ||
| signal to noise ratio: | > 104 dB (unweighted) | ||
| DC offset voltage: | < 10 mV | ||
| common mode rejection (output impedance): | > 60 dB | ||
| common mode rejection (output voltage): | > 40 dB | ||
| converter technology: | 24 bit, oversampling sigma-delta | ||
Further Information
| power consumption: | 25 W | ||
| sample frequency: | 48 kHz or 44.1 kHz (automatically synchronised to the configured device system sample frequency) | ||
| connector style: | mic input: XLR-3 female headphones output: combined XLR-3 female/ 1/4“ TRS jack analogue line outputs: XLR-3 male unbal. analoge stereo in/mono out: 4-pin 3.5mm CTIA |
||
Note
All values are typical values.
Warning
The wiring of microphone inputs of DHD microphone input modules is not designed to support operation with parallel external phantom power. Using it might result in damages of the pre-amplifier or phantom power generator.
Any Input to Any Output
Measured from any analogue or digital input to any analogue or digital output
| frequency response: | < 0.2 dB, 20Hz - 20kHz |
| THD+N | < -80 dB / 0.01% (@ -1 dBFS) |
| signal to noise ratio: | > 95 dB |
Note
All values are typical values. Measured between modules 52-7111, 52-7112, 52-7230, 52-7235, 52-7255, 52-7258, 52-7222, 52-7223, 52-7224.