Version 10.2 release notes and upgrade instructions

Version 10.2 release notes and upgrade instructions

Firmware and Toolbox version 10.2 focus on evolving features and functionality introduced with XC3 & XD3 and version 10.1.

If an upgrade of your hardware is required and you are unsure how to handle this process, please contact your local DHD distributor - see List of DHD distributors.

New Features

General

Support for XS3 Core
Support for XD3 Quad Core 52-7554
Support for Thimeo Stereo Tool on XD3 Quad Core 52-7554
Re-organized licensing:
- 52-8594 System Upgrade License postponed for upgrades from FW 10.1.14 or higher to version 10.2
- Introduction of License Serial instead of Micro SD Serial or SSD Serialfor licensing:
  - License Serial is shown in the System App
  - on 52-7500 XS3 Cores the License Serial will be the Wnnnnnnnnn number
  - on 52-752x XC3 Cores the License Serial will always be the serial of the factory installed MicroSD card –> the Cnnnnnnnnn number
  - on 52-755x XD3 Cores the License Serial will always be the serial of the factory installed SSD storage –> the Dnnnnnnnnn number
- with introduction of the License Serial, licenses are always stored inside the DHD Core hardware
- in the case of a defect of the MircoSD or SSD card, it can be easily replaced, without the need of re-licensing and re-bundling the replacement card
- new X*3 Cores that are planned to be spare parts, should be pre-licensed in an adequate way, as swapping SD/SSD cards will not help any more from the license perspective from V10.2
Aux Sends on Fader
switchable MADI SRC available on
- XS3 Core: MADI Port
- XC3 Core: GA 1
- XD3 Core: GA 1/ GA 9 / GA 13 / GA 17 / GA 21 - not available on GA 5
Improved AGC/Loudness AGC Freeze:
- (L)AGC Autofreeze feature 'Freeze (L)AGC when Fader Start OFF' now also depends on the Automix (if used). This should prevent unwanted (L)AGC regulation while the channel is not used or spoken to.
- (L)AGC Freeze key function: now supports a 3rd color to indicate that 'autofreeze' is active

Firmware

overhauled internal procedures in Logic and Audio System

Toolbox

SX2 Wizard available for 52-7500 XS3 Cores

Security Features & Web Apps

Devices with Version 10.2 installed now automatically generate a self signed certificate for encrypted web communication
the following pre-conditions must be met to make use of the self signed certificate:
- no individual certificate may be installed
- valid NTP time server must be setup & system time must be synced
- HTTPs communication must be enabled in the System App's Services menu

Important
The use of self signed certificates requires the user to initially accept a browser's security warning and/or to add an exception rule.

AES67 & Dante modules

Note
No version 10.2 update available yet for 52-7567 AES67 or 52-7580/7585/7080B Dante modules.
These modules can be still be operated with their firmware/kernel version 10.0 or 10.1 without problems - even if the DHD Core is running on Version 10.2.

Upgrade Instructions - Kernel & Firmware

Important
Before upgrading to Version 10.2 ensure that the Core is updated to the latest Firmware 10.1 - minimum FW 10.1.14.

Note
The upgrade and further updates are now rolled out within a single DeviceOS update package file.
This file can be applied like any other update file as knwon from before. The main difference is that all necessary software updates are now applied in one single step.

The file extension is:

xc3p DeviceOS for XC3 Cores.
xd3p DeviceOS for XD3 Cores.

Important
The XD3 Update (Kernel & Firmware) takes approx. 2-3 minutes to finish. Do not switch off or restart the device during the update.</wrap>

Upgrade Instructions - Toolbox Project

As no major changes are introduced in Toolbox version 10.2, upgrading from version 10.1 to 10.2 should work by opening the existing project file within Toolbox 10.2 and checking if any messges are issued.

For a seamless transition, we recommend planning with enough spare time to convert your Toolbox project.

First of all, you need to have your Toolbox working at the latest Toolbox v10.1.x. If this condition is fulfilled, open your .dp10 project file with Toolbox v10.2.x.

Important
We strongly recommend to keep a copy of the original v10.1.x (.dp10) project file.

You may receive some WARNING messages in the Messages Section. Those messages inform you if your Toolbox project is using no longer supported hardware, if other problems occurred or if adjustments were done during conversion of the project. A double click on the message leads you to the hardware module or part of the configuration that is subject of the message.

Table of Contents