Differences
This shows you the differences between two versions of the page.
sx:system_settings [2016/12/16 14:41] go informations-->information |
sx:system_settings [2021/02/02 14:31] |
||
---|---|---|---|
Line 1: | Line 1: | ||
- | <- sx:hardware|Hardware ^ sx:start|52/SX Configuration ^ sx:io_settings|I/O Settings -> | ||
- | |||
- | |||
- | |||
- | |||
- | ======System Settings====== | ||
- | |||
- | On the ''System Settings'' page, you can configure general options for your 52/SX. | ||
- | |||
- | [{{ :sx:system_settings.png?nolink |//SXConfig Software - System Settings//}}] | ||
- | |||
- | In the following sections you can find the descriptions for these options. | ||
- | |||
- | ===== Synchronisation ===== | ||
- | |||
- | Select here, which sample rate should be set for internal synchronisation (44.1 kHz / 48 kHz). | ||
- | |||
- | Select in the ''Select Source'' list, which sync source should be used: | ||
- | |||
- | * Internal - internal clock | ||
- | * BNC Wordclock (rising edge) (optional) | ||
- | * BNC Wordclock (falling edge) (optional) | ||
- | * BNC AES/EBU (optional) | ||
- | * Dante 4x4 | ||
- | * GA1 / GA2 (Gigabit Audio) (optional) | ||
- | * MADI1 / MADI2 (optional) | ||
- | |||
- | ===== Fader Program Key Mode ===== | ||
- | |||
- | In this area you can change the behaviour of the Fader Program Keys. | ||
- | |||
- | * ''PGM On/Off'': If you press the Program 1 or Program 2 key on the fader module the channel is activated or deactivated on the corresponding Program bus. | ||
- | * ''PGM1 Off Air'': If the Program 1 key is deactivated, the channel is routed to OffAir bus. | ||
- | |||
- | ===== TFT State Indicators ===== | ||
- | |||
- | [{{ :sx:sx_stateindicators.png?nolink |//TFT State Indicators//}}] | ||
- | |||
- | You can change text, behaviour and look of the TFT state indicators. | ||
- | |||
- | In the Table | ||
- | * ''Element'': All four available status transparents are shown in this list. | ||
- | * ''Text'': Double-click on the text to change it. | ||
- | * ''Color'': Double-click on the color field to change it. A Dropdown menu opens. | ||
- | * ''Condition'': Double-click on the logic condition, the Logic sources window opens. Select the desired logic and click assign. | ||
- | |||
- | The ''Logic Condition'' under the Table allows you to select the logic condition. When you have selected a list entry in the table, click ''Select''. The logic source window opens. Select the desired logic and click assign. | ||
- | |||
- | <WRAP center round info 80%> | ||
- | **Note**\\ Logic conditions are DHD internal functions. A logic source can be true (1) or false (0). Logic sources can be GPIs, Keys/TFT Buttons, Level or Correlation Detects or system state functions. For more information on Logic see [[tb8:logic|Toolbox 8 Documentation: General information on Logic]]. | ||
- | </WRAP> | ||
- | |||
- | <WRAP center round important 80%> | ||
- | **Important**\\ If more special logic sources are required or you need to work with logics (logic functions), enhanced feature license and Toolbox 8 is required. | ||
- | |||
- | Ember+ as an additional logic source is also possible. Contact your DHD dealer or DHD directly for further information on upgrading your system. | ||
- | </WRAP> | ||
- | |||
- | ===== Peakmeter Option ===== | ||
- | |||
- | You can change behaviour of the PPMs. | ||
- | |||
- | * ''Scale Color'': Select the colour of the peak program meter on the TFT display. The selected colour is used for all peak program meters of the 52/SX. | ||
- | * ''Scale Type'': Select your preferred type of peak meter scale. | ||
- | * ''Red Bar Over (dB)'': Select the decibel value at which the level bar turns red for signaling a critical level area. (-20 dB to +20 dB) | ||
- | * ''Zero Offset (dB)'': Select the decibel value, which will be added to the level bar to adjust the shown signal level. | ||
- | |||
- | ===== Licensing ===== | ||
- | |||
- | You can use additional Licenses for more advanced features. | ||
- | |||
- | * ''Use 52-8583 XC/XS Core Control Networking'': To enable the features of the XC/XS Core Control Networking license select this check box.\\ \\ <WRAP center important 80%>**Important**\\ The configuration can only be loaded into the device, if the corresponding license key is assigned to this device.</WRAP> | ||
- | *'' Send Logic Control Information'': Enables the Device to exchange logic information with other cores that have this license and are in the same project. (16 Devices maximum possible) | ||
- | * ''Use 52-8582 XC/XD/XS Core Audio Network'': To enable the features of the XC/XS Core Audio Network license select this check box.\\ \\ <WRAP center important 80%>**Important**\\ The configuration can only be loaded into the device, if the corresponding license key is assigned to this device.</WRAP> | ||
- | * ''Use 52-8581 Enhanced DSP Processing'': To enable the features of the Enhanced DSP Processing license select this check box.\\ \\ <WRAP center important 80%>**Important**\\ The configuration can only be loaded into the device, if the corresponding license key is assigned to this device.</WRAP> | ||
- | |||
- | <WRAP center round info 80%> | ||
- | **Note**\\ For general Information on licensing see [[licensing:start|Licensing]]. | ||
- | </WRAP> | ||
- | <WRAP center round info 80%> | ||
- | **Note**\\ When you have a valid license code, you have to enter it directly into your core. After this done, you have to allow the license here for the configuration software. | ||
- | |||
- | See [[tb8:maintenance:device#enter_license|Maintenance / Enter License]] for information on entering a license into your core. | ||
- | </WRAP> |