Differences

This shows you the differences between two versions of the page.

Link to this comparison view

sx:v7:buses [2019/03/11 15:49]
sx:v7:buses [2021/02/02 14:31] (current)
Line 1: Line 1:
 +<- sx:​v7:​monitoring|Monitoring & Talkback ​ ^ sx:​v7:​start|52/​SX Configuration ^ sx:​v7:​on_air_switch|On-Air-Switch ​ ->
  
 +
 +
 +
 +
 +
 +
 +
 +
 +
 +
 +
 +
 +
 +
 +
 +
 +
 +
 +
 +
 +
 +
 +
 +
 +
 +
 +
 +======Buses======
 +
 +On the ''​Buses''​ page you can configure the settings for all buses that are available in the 52/SX system. ​
 +
 +[{{ :​sx:​v7:​buses.png?​nolink |SXConfig Software - Buses}}]
 +
 +In the following tables all options on this page are explained.
 +
 +|  **element** ​ |  **description** ​ |
 +|Talk 1 Source|Click the {{:​sx:​on-air_switch_dots.png?​nolink}} button, next to the ''​Talk 1 Source''​ box. The ''​Audio Sources''​ window opens. Select a audio source from the list and click assign.\\ When the ''​Talk 1 Condition''​ logic becomes true, the ''​Talk 1 Source''​ is active on the corresponding bus.|
 +|Talk 2 Source|Click the {{:​sx:​on-air_switch_dots.png?​nolink}} button, next to the ''​Talk 2 Source''​ box. The ''​Audio Sources''​ window opens. Select a audio source from the list and click assign.\\ When the ''​Talk 2 Condition''​ logic becomes true, the ''​Talk 2 Source''​ is active on the corresponding bus.|
 +|Talk Attenuation|When a Talk Source is active, the busses can be attenuated between ''​0 dB''​ and ''​Off''​ in steps of 1 dB. Use the ''​Talk Attenuation''​ selector to change the attenuation value.|
 +
 +|  **column** ​ |  **description** ​ |
 +|Bus name|Here you can find the name of the bus for which you configure the following settings.|
 +|Stereo|Select this check box, if the bus is stereo. Clear the check box to configure the bus as mono.|
 +|Talk 1 Condition|Click the {{:​sx:​on-air_switch_dots.png?​nolink}} button, next to the ''​Talk 1 Condition''​ box. The ''​Logic Sources''​ window opens. Select a logic source from the list and click assign.\\ When this logic source becomes true, the ''​Talk 1 Source''​ is active on the corresponding bus.|
 +|Talk 2 Condition|Click the {{:​sx:​on-air_switch_dots.png?​nolink}} button, next to the ''​Talk 2 Condition''​ box. The ''​Logic Sources''​ window opens. Select a logic source from the list and click assign.\\ When this logic source becomes true, the ''​Talk 2 Source''​ is active on the corresponding bus.|
 +|Limiter|Select the ''​On''​ check box to activate the limiter for this bus. \\ Select a threshold value from the drop-down menu (-30 dB to 20 dB).|
 +|CF Source|Select from the drop down menu an audio source for your clean feed signal|
 +|Use Output select|Select this check box to enable source selection for the alternative clean feed signal.|
 +|Add to Selector List 1|Select this check box to add a bus to source list 1. This bus will be available in the monitor source list, which is assigned to the ''​Selector''​ key on 52-1010 central module.|
 +|Add to Selector List 2|Select this check box to add a bus to source list 2. This bus will be available for monitoring in the''​ Monitor 2 ''​list,​ which is available in the ''​Selector''​ view of the TFT/Touch Display.|