Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision 		Previous revision
sx:v7:central_module [2016/11/29 17:25]
go 		sx:v7:central_module [2017/06/15 17:20]
admin
Line 15: Line 15:
 {{:​sx:​52-1010_front_highlight.zoom65.png?​nolink |}} {{:​sx:​52-1010_front_highlight.zoom65.png?​nolink |}}
  
-**1.** Pre-listening and talkback speaker with built-in amp \\ No additional audio cable is required for this central module. The audio signals will be transported together with control signals and PoE through one CAT5 cable, which is connected to the APC port on the XS Core.+**1.** Pre-listening and talkback speaker with built-in amp \\ No additional audio cable is required for this central module. The audio signals will be transported together with control signals and electrical power through one CAT5 cable, which is connected to the APC port on the XS Core.
 ---- ----
 **2.** Encoder section for control of EQs, dynamics and other settings\\ To change parameters of a selected channel, press the''​ Input'',​ ''​EQ'',​ ''​Dynamic''​ or ''​Aux''​ key to switch between the TFT pages.\\ The 52-1010 has four coloured encoders. Use them to control parameters for EQ, dynamics, Aux etc. on the TFT/Touch display. You can see a coloured frame around the parameters on the TFT display, this colour shows, which encoder controls which parameter.\\ To recall default values for the whole mixing console, press the ''​Load Default''​ key one second. In that case, snapshot 0, which is the default mixer snapshot, is loaded.\\ Press the ''​Snapshot''​ key to show the ''​Snapshot''​ view on the TFT. There, you can save up to 20 different mixer snapshots. If a channel is selected, the ''​Snapshots''​ view shows the available channel snapshots. There, you can save up to 50 different channel snapshots. **2.** Encoder section for control of EQs, dynamics and other settings\\ To change parameters of a selected channel, press the''​ Input'',​ ''​EQ'',​ ''​Dynamic''​ or ''​Aux''​ key to switch between the TFT pages.\\ The 52-1010 has four coloured encoders. Use them to control parameters for EQ, dynamics, Aux etc. on the TFT/Touch display. You can see a coloured frame around the parameters on the TFT display, this colour shows, which encoder controls which parameter.\\ To recall default values for the whole mixing console, press the ''​Load Default''​ key one second. In that case, snapshot 0, which is the default mixer snapshot, is loaded.\\ Press the ''​Snapshot''​ key to show the ''​Snapshot''​ view on the TFT. There, you can save up to 20 different mixer snapshots. If a channel is selected, the ''​Snapshots''​ view shows the available channel snapshots. There, you can save up to 50 different channel snapshots.
Line 21: Line 21:
 **3.** Flexible encoder & OLED display section for additional volume and monitor selectors, studio support. (see [[sx:​v7:​console|52/​SX Configuration - Console]]) **3.** Flexible encoder & OLED display section for additional volume and monitor selectors, studio support. (see [[sx:​v7:​console|52/​SX Configuration - Console]])
 ---- ----
-**4.** GP  - General Purpose keys\\ You can use these keys to switch GPOs  and get status signalisation from a GPI, or any other available logic source. You can also use these keys to switch the function of one of the encoders next to the OLED-Display. (see [[sx:​console|52/​SX Configuration - Console]])+**4.** GP  - General Purpose keys\\ You can use these keys to switch GPOs  and get status signalisation from a GPI, or any other available logic source. You can also use these keys to switch the function of one of the encoders next to the OLED-Display. (see [[sx:v7:​console|52/​SX Configuration - Console]])
 ---- ----
 **5.** Talkback microphone with built-in preamp \\ The 52-1010 is the first Series 52 control module with built-in talkback microphone. No additional audio cable is required for this central module. The audio signals will be transported together with control signals and PoE through one CAT5 cable, which is connected to the APC port on the XS Core. **5.** Talkback microphone with built-in preamp \\ The 52-1010 is the first Series 52 control module with built-in talkback microphone. No additional audio cable is required for this central module. The audio signals will be transported together with control signals and PoE through one CAT5 cable, which is connected to the APC port on the XS Core.
Line 27: Line 27:
 **6.** Professional high-grade volume potentiometers **6.** Professional high-grade volume potentiometers
 ---- ----
-**7.** Monitor selector, expanded by touch-display selector (see [[sx:​console|52/​SX Configuration - Console]])+**7.** Monitor selector, expanded by touch-display selector (see [[sx:v7:​console|52/​SX Configuration - Console]])
 ---- ----
-**8.** Talkback keys\\ It is possible to configure these keys for a simple talkback, for example to a sound booth or an additional 52/SX mixing console. (see [[sx:​console|52/​SX Configuration - Console]])+**8.** Talkback keys\\ It is possible to configure these keys for a simple talkback, for example to a sound booth or an additional 52/SX mixing console. (see [[sx:v7:​console|52/​SX Configuration - Console]])

© 2024 DHD audio GmbH | | Imprint | Privacy Agreement | General Terms & Conditions

Specifications and design are subject to change without notice. The content of this document is for information only. The information presented in this document does not form part of any quotation or contract, is believed to be accurate and reliable and may be changed without notice. No liability will be accepted by the publisher for any consequence of its use. Publication thereof does neither convey nor imply any license under patent rights or other industrial or intellectual property rights.