Differences
This shows you the differences between two versions of the page.
|
sx:v7:hardware [2016/11/29 17:53] go [XS Core] |
sx:v7:hardware [2019/03/11 15:49] |
||
|---|---|---|---|
| Line 1: | Line 1: | ||
| - | <- sx:v7:general|General information on Configuration ^ sx:v7:start|52/SX Configuration ^ sx:v7:system_settings|System Settings -> | ||
| - | |||
| - | |||
| - | |||
| - | |||
| - | ======Hardware====== | ||
| - | |||
| - | [{{ :sx:v7:hardware.png?nolink |//SXConfig Software - Hardware//}}] | ||
| - | |||
| - | On the ''Hardware'' page you can set which 52/SX modules are connected to your system. | ||
| - | |||
| - | |||
| - | ===== Common Settings Area ===== | ||
| - | |||
| - | In the Field ''Device name'', enter a distinctive device name for this 52/SX mixing console. | ||
| - | |||
| - | |||
| - | ===== SX Fader Module ===== | ||
| - | |||
| - | ''Select Type'': | ||
| - | * In the left drop-down menu, select 52-1020 or 52-1024 depending on your fader modules. | ||
| - | * In the right drop-down menu, select the number of faders. | ||
| - | |||
| - | ===== XS Core ===== | ||
| - | |||
| - | Select your core type. Select 52-1804 if you want to configure a 4 fader mixer or select 52-1801 for 8-16 fader. | ||
| - | |||
| - | * ''Use MADI Module 52-1821'': If your XS core is equipped with a MADI module 52-1821, please select this check box to enable the inputs and outputs for the ''I/O Settings'' tab. | ||
| - | * ''Use Gigabit Audio 52-7391'': If your XS core is equipped with a Gigabit Audio SFP Module, this enables the inputs and outputs in the ''I/O Settings'' tab. Gigabit Audio is useful e.g. to interlink with other DHD devices. | ||
| - | |||
| - | |||
| - | |||
| - | ===== XS I/O connections ===== | ||
| - | |||
| - | |||
| - | * ''APC 8'' (or APC 4 when using 52-1830 XS Core)|Select an I/O type or set the value to'' (none)''. Default is'' 52-1335''. | ||
| - | * ''APC 7'' (not available when using 52-1830 XS Core)|Select an I/O type or set the value to'' (none)''. Default is'' 52-1335''. | ||
| - | * ''APC 6'' (not available when using 52-1830 XS Core)|Select an I/O type or set the value to'' (none)''. Default is'' (none)''. | ||
| - | |||
| - | When you check ''Use 52-8511 PC TFT View Software'', you can additionally assign a hardware module to ''APC 1''. This is possible because you do not need an 52-4018 TFT module. | ||
| - | |||
| - | <WRAP center round important 80%> | ||
| - | **Important**\\ 52-8511 PC TFT View Software requires valid License! | ||
| - | </WRAP> | ||
| - | |||
| - | ===== Console Preview ===== | ||
| - | |||
| - | ''Split'': Shows a split version of the control modules in the preview. | ||
| - | ''Flat'': Shows the control modules build in a flat table installation frame instead of a console frame. | ||