Differences

This shows you the differences between two versions of the page.

Link to this comparison view

sx:v7:on_air_switch [2019/03/11 15:49]
sx:v7:on_air_switch [2020/06/04 10:41] (current)
Line 1: Line 1:
 +<- sx:​v7:​buses|Buses ​ ^ sx:​v7:​start|52/​SX Configuration ^ sx:​v7:​users|Users ​ ->
  
 +
 +
 +
 +
 +
 +
 +
 +
 +
 +
 +
 +
 +
 +
 +
 +
 +
 +
 +
 +
 +
 +
 +
 +
 +
 +
 +
 +======On-Air Switch======
 +
 +The ''​On-Air Switch''​ page gives you the possibility to change sources for an output controlled by logic sources.
 +
 +[{{ :​sx:​v7:​on-air_switch.png?​nolink |//SXConfig Software - On Air Switch//}}]
 +
 +You can select three stereo audio sources, which can be switched by two logic sources. ​
 +
 +On the left-hand side you can see the audio sources of the On-Air switch. The black lines symbolise audio signal paths. There are two blue-coloured signal switches, each with an associated logic sources (see figure On-Air Switch configuration). ​
 +
 +[{{ :​sx:​on-air_switch_general.png?​nolink |//On-Air Switch configuration//​}}]
 +
 +To configure the On-Air switch, follow these steps:
 +
 +  - Click the {{:​sx:​on-air_switch_dots.png?​nolink}} button next to the ''​Source 1L''​ box, the ''​Audio Sources''​ window opens. ​
 +  - In the ''​Audio Sources''​ window, select a source and click ''​Assign''​. Alternatively you can double-click on the source or drag it to the ''​Source''​ box. The source is now assigned to the On-Air switch. ​
 +  - Repeat steps 1 and 2 for the ''​Sources 1R, 2L, 2R, 3L''​ and ''​3R''​.
 +  - The main switch on the right-hand side is assigned by default to the ''​OnAir''​ Logic Function. To change the logic source, click {{:​sx:​on-air_switch_dots.png?​nolink}} and select another logic source from the ''​Logic Sources''​ window.
 +  - The switch between ''​Source 1''​ and ''​Source 2''​ has no default logic source and you have to select a logic source if ''​Source 2''​ will be used. Click {{:​sx:​on-air_switch_dots.png?​nolink}} and select another logic source from the ''​Logic Sources''​ window.
 +
 +The main switch with its default logic source OnAir is already preconfigured in the 52/​SX-System. To switch between ''​Source 3''​ and ''​Source 1''​ (or ''​Source 2''​) follow these steps:
 +
 +  - On the TFT/Touch Display, on the main page, tap on ''​add. Settings''​.
 +  - Tap on the ''​ON AIR''​ button and press at the same time the ''​OK''​ key on the central module (52-1010). The ''​ON AIR''​ button turns red.''​ Source 3''​ is now selected.
 +  - To switch back to ''​Source 1''​ (or ''​Source 2''​),​ tap on the ''​OFF AIR''​ button and press at the same time the ''​OK''​ key on the central module (52-1010). The ''​OFF AIR''​ button turns green and the ''​ON AIR''​ button turns white.''​ Source 1''​ is now selected.
 +
 +In the ''​On Air Switch Signal''​ area, you can assign the On Air Switch Signal to the''​ Selector List 1''​ and ''​Selector List 2''​. You can find these lists on the ''​Selector''​ view of the TFT/Touch Display.
 +
 +The Label and color for the corresponding TFT buttons can be changed in the ''​TFT Keyoptions''​ area.